EUVIMEDObjevte EUVIMED
Video/Audio

Impact of Fabrication Techniques and Polishing Procedures on Surface Roughness of Denture Base Resins

Yunus Emre Ozden, Pinar Yilmaz Atali, Zeynep Ozkurt Kayahan

Journal of Visualized Experiments · 2025-01-17 · (215)

DOI: 10.3791/67844 ↗

At a glance

Video/Audio in Journal of Visualized Experiments, published online on 2025-01-17. Written by Yunus Emre Ozden and 2 co-authors. Institution: Faculty of Dentistry Department of Prosthodontics, Yeditepe University; emre.ozden@yeditepe.edu.tr. Major MEDLINE topics: Denture Bases, Dental Polishing, Resins, Synthetic. Cited 2 times so far (Crossref); 35 references.

AbstraktSubjectsBibliografické údajeCiteRelated studies

Abstract (original language)

This study aimed to assess the impact of various fabrication techniques and polishing procedures on the surface roughness (Ra) of resin-based materials used in the fabrication of complete dentures. A total of 90 specimens were produced from three different resin materials: heat-polymerized polymethyl methacrylate (PMMA) resin, CAD-CAM milled PMMA resin, and 3D-printed resin (n = 30). Each specimen measured 10 mm in diameter and 2 mm in height. The surface roughness (Ra) values of the specimens were initially determined using a contact profilometer following fabrication. Subsequently, each group of specimens was polished with 600-, 800-, and 1000-grit silicon carbide abrasive papers under running water. A second measurement of the surface roughness (Ra) values was then performed. The data were analyzed statistically using the Kruskal-Wallis test, Mann-Whitney U test, Wilcoxon signed-rank test, and paired samples t-test (p = 0.05). A statistically significant difference was identified between the groups in terms of surface roughness (Ra) prior to the polishing process (p < 0.001). However, no statistically significant difference was observed between the milled and heat-polymerized PMMA base materials following the polishing process. The 3D-printed specimens showed the most notable improvement in surface roughness due to the polishing process. Nevertheless, their surface roughness remained statistically significantly higher compared to the other samples, both before and after polishing (p < 0.001). The fabrication method of complete denture base materials was observed to influence surface roughness. The surface roughness values of the base materials fabricated using the 3D printing method were higher compared to those fabricated with milled and heat-polymerized PMMA resin, both before and after polishing.

Subjects

MeSH terms (MEDLINE)

Denture BasesDental PolishingResins, SyntheticPolymethyl MethacrylateSurface PropertiesPrinting, Three-Dimensional

Substances

Polymethyl MethacrylateResins, Synthetic

Authors and institutions

  • Faculty of Dentistry Department of Prosthodontics, Yeditepe University; emre.ozden@yeditepe.edu.tr.
  • Faculty of Dentistry Department of Restorative Dentistry, Marmara University.
  • Faculty of Dentistry Department of Prosthodontics, Yeditepe University.

Cite

APA

Ozden, Y. E., Yilmaz Atali, P., & Ozkurt Kayahan, Z. (2025). Impact of Fabrication Techniques and Polishing Procedures on Surface Roughness of Denture Base Resins. Journal of Visualized Experiments. https://doi.org/10.3791/67844

Vancouver

Ozden YE, Yilmaz Atali P, Ozkurt Kayahan Z. Impact of Fabrication Techniques and Polishing Procedures on Surface Roughness of Denture Base Resins. Journal of Visualized Experiments. 2025. doi:10.3791/67844

BibTeX
@article{Ozden2025,
  author = {Ozden, Yunus Emre and Yilmaz Atali, Pinar and Ozkurt Kayahan, Zeynep},
  title = {Impact of Fabrication Techniques and Polishing Procedures on Surface Roughness of Denture Base Resins},
  journal = {Journal of Visualized Experiments},
  year = {2025},
  number = {215},
  doi = {10.3791/67844}
}
Start for free →