EUVIMEDEUVIMED entdecken
VergleichsstudieOpen Access · CC BY 4.0

Comparative laboratory study of 3D printed denture base resin materials

Ioli Ioanna Artopoulou, Eleftheria Pani, George Eliades

The Journal of Prosthetic Dentistry · 2025-11 · 134 (5) · 1964.e1-1964.e9

DOI: 10.1016/j.prosdent.2025.08.007 ↗

Kurz gefasst

Vergleichsstudie in der Zeitschrift The Journal of Prosthetic Dentistry, 2025-11. Verfasst von Ioli Ioanna Artopoulou und 2 weiteren Autor:innen. Beteiligte Einrichtung: Associate Professor, Department of Prosthodontics, School of Dentistry, National and Kapodistrian University of Athens, Athens, Greece; and f. Fellow…. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Denture Bases, Dental Materials, Resins, Synthetic. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 58 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: VOCO.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: Several 3-dimensionally (3D) printed denture base resin materials designed for removable dentures and maxillofacial prostheses have recently been introduced, but studies on their properties are lacking. PURPOSE: The purpose of this in vitro study was to assess the degree of conversion (DC%), Vickers hardness (VHN), crosslinking density (CD), tensile strength (TS), surface roughness (SR), and wettability (W) of two 3D printed denture base materials in comparison with a heat-polymerized polymethyl methacrylate (PMMA) control. MATERIAL AND METHODS: Disk- (Ø15×3 mm) and dumbbell-shaped (International Organization for Standardization (ISO) 527-1 standard) specimens of two 3D printed denture base materials (V Print-dentbase) and (Optiprint Laviva) were printed, and PMMA specimens (Acrypol fast) were used as the control. DC% (n=5) was measured by Fourier Transform Infrared spectroscopy, VHN and CD (n=10) with a Vickers hardness tester, and TS (including modulus of elasticity-E and elongation-e, n=10) using a universal testing machine. SR parameters (Sa, Sq, Sz, Sdr, Sc, Sv, n=10) were measured with an optical profiler and water contact angles (θ) (apparent/θm and Young/θy, n=10) with a contact angle goniometer. Data were analyzed with t tests, the Mann-Whitney Rank Sum test, and 1-way ANOVA (α=.05). RESULTS: For DC%, the control was greater than the VP-dentbase (P .05). For VHN, the ranking was OP>VP and AF. Differences in CD were not significant. For TS and E the ranking was VP, AF>OP, with differences between VP and AF not significant. ε was zero for all materials. For SR parameters, the ranking was OP AF (for Sdr). No significant differences were found in θm and θy among the materials or between θm and θy per material (P>.05). CONCLUSIONS: The different chemical compositions of the 3DPs resulted in significant differences in some of the tested properties.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalDenture BasesDental MaterialsResins, SyntheticPolymethyl MethacrylateMaterials TestingSurface PropertiesTensile StrengthHardnessWettabilityAcrylic Resins

Substanzen

Polymethyl MethacrylateDental MaterialsResins, SyntheticAcrylic Resins

Autor:innen und Institutionen

  • Associate Professor, Department of Prosthodontics, School of Dentistry, National and Kapodistrian University of Athens, Athens, Greece; and f. Fellow, M.D. Anderson Cancer Center, University of Texas, Houston, TX. Elect…
  • PhD Candidate, Department of Prosthodontics, School of Dentistry, National and Kapodistrian University of Athens, Athens, Greece.
  • Professor, Department of Biomaterials, School of Dentistry, National and Kapodistrian University of Athens, Athens, Greece.

Förderung

  • VOCO

Zitieren

APA

Artopoulou, I. I., Pani, E., & Eliades, G. (2025). Comparative laboratory study of 3D printed denture base resin materials. The Journal of Prosthetic Dentistry, 134(5), 1964.e1-1964.e9. https://doi.org/10.1016/j.prosdent.2025.08.007

Vancouver

Artopoulou II, Pani E, Eliades G. Comparative laboratory study of 3D printed denture base resin materials. The Journal of Prosthetic Dentistry. 2025;134(5):1964.e1-1964.e9. doi:10.1016/j.prosdent.2025.08.007

BibTeX
@article{Artopoulou2025,
  author = {Artopoulou, Ioli Ioanna and Pani, Eleftheria and Eliades, George},
  title = {Comparative laboratory study of 3D printed denture base resin materials},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2025},
  volume = {134},
  number = {5},
  pages = {1964.e1--1964.e9},
  doi = {10.1016/j.prosdent.2025.08.007}
}
Kostenlos starten →