Effect of polishing and denture cleansers on the surface roughness of new‐generation denture base materials and their color change after cleansing
Journal of Prosthodontics · 2024-10 · 33 (8) · 783-790
DOI: 10.1111/jopr.13755 ↗Kurz gefasst
Fachartikel in der Zeitschrift Journal of Prosthodontics, online erschienen am 08.09.2023. Verfasst von Gülce Çakmak und 7 weiteren Autor:innen. Beteiligte Einrichtung: Department of Reconstructive Dentistry and Gerodontology, School of Dental Medicine, University of Bern, Bern, Switzerland. Hauptthemen laut MEDLINE: Denture Cleansers, Surface Properties, Dental Polishing, Denture Bases. Die Arbeit wurde bisher 17-mal zitiert (Crossref) und nennt 33 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
Purpose
To evaluate the effect of polishing and denture cleansers on the surface roughness ( R a ) of new‐generation denture base materials that are additively, subtractively, and conventionally fabricated, while also assessing their color change after cleansing. Material and Methods One hundred and fifty disk‐shaped specimens (Ø10 × 2 mm) were prepared from five denture base materials (one subtractively manufactured nanographene‐reinforced prepolymerized polymethylmethacrylate (PMMA) (SM‐GC), one subtractively manufactured prepolymerized PMMA (SM‐PM), two additively manufactured denture base resins (AM‐DT and AM‐ND), and one heat‐polymerized PMMA (CV) ( n = 30). The R a of the specimens was measured before and after conventional laboratory polishing, while color coordinates were measured after polishing. Specimens were then divided into three subgroups based on the denture cleanser: distilled water, 1% sodium hypochlorite (NaOCl), and effervescent tablet ( n = 10). The R a and color coordinates were remeasured after nine cleansing cycles over a period of 20 days. The CIEDE2000 formula was used to calculate the color differences (Δ E 00 ). Two‐way analysis of variance (ANOVA) was used to analyze the R a values before ( n = 30) and after ( n = 10) cleansing, while repeated measures ANOVA was used to analyze the R a of material‐time point pairs within each denture cleanser ( n = 10). Δ E 00 data after denture cleansing was also analyzed by using two‐way ANOVA ( n = 10) ( α = 0.05).
Results
Before polishing, R a varied significantly among the materials. SM‐GC and SM‐PM had the lowest and AM‐ND the highest R a values ( P < 0.001). Polishing significantly reduced R a of all materials ( P < 0.001), and after polishing, R a differences among materials were nonsignificant ( P ≥ 0.072). Regardless of the denture cleanser, the R a of AM‐DT, AM‐ND, and CV was the highest before polishing when different time points were considered ( P < 0.001). After cleansing, AM‐ND had the highest R a of all the materials, regardless of the cleanser ( P ≤ 0.017). AM‐DT had higher R a than SM‐PM when distilled water ( P = 0.040) and higher R a than SM‐GC, SM‐PM, and CV when NaOCl was used ( P < 0.001). The type of cleanser significantly influenced the R a of AM‐DT, AM‐ND, and CV. For AM‐DT, NaOCl led to the highest R a and the tablet led to the lowest R a ( P ≤ 0.042), while for AM‐ND, distilled water led to the lowest R a ( P ≤ 0.024). For CV, the tablet led to lower R a than distilled water ( P = 0.009). Color change varied among the materials. When distilled water was used, SM‐GC had higher Δ E 00 than SM‐PM and AM‐DT ( P ≤ 0.034). When NaOCl was used, AM‐ND had higher Δ E 00 than SM‐GC, SM‐PM, and AM‐DT, while CV and SM‐GC had higher Δ E 00 than SM‐PM and AM‐DT ( P ≤ 0.039). Finally, when the tablet was used, AM‐ND and CV had the highest Δ E 00 , while AM‐DT had lower Δ E 00 than SM‐GC ( P ≤ 0.015).
Conclusions
The tested materials had unacceptable surface roughness (>0.2 μm) before polishing. Roughness decreased significantly after polishing (
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Department of Reconstructive Dentistry and Gerodontology, School of Dental Medicine, University of Bern, Bern, Switzerland.
- Department of Prosthodontics, Faculty of Dentistry, Istinye University, Istanbul, Turkey.
- Department of Prosthodontics, Faculty of Dentistry, Alanya Alaaddin Keykubat University, Antalya, Turkey.
- Dental Health Department, College of Applied Medical Sciences, King Saud University, Riyadh, Saudi Arabia.
- Division of Gerodontology and Removable Prosthodontics, University Clinics of Dental Medicine, University of Geneva, Geneva, Switzerland.
- Department of Restorative, Preventive and Pediatric Dentistry, School of Dental Medicine, University of Bern, Bern, Switzerland.
ORCID-Profile: Gülce Çakmak, Mustafa Borga Dönmez, Deniz Yılmaz, Abdulaziz Alhotan, Burak Yilmaz
Zitieren
APA
Çakmak, G., Hess, J. A., Dönmez, M. B., Yılmaz, D., Alhotan, A., Schimmel, M., Peutzfeldt, A., & Yilmaz, B. (2024). Effect of polishing and denture cleansers on the surface roughness of new‐generation denture base materials and their color change after cleansing. Journal of Prosthodontics, 33(8), 783-790. https://doi.org/10.1111/jopr.13755
Vancouver
Çakmak G, Hess JA, Dönmez MB, Yılmaz D, Alhotan A, Schimmel M, et al. Effect of polishing and denture cleansers on the surface roughness of new‐generation denture base materials and their color change after cleansing. Journal of Prosthodontics. 2024;33(8):783-790. doi:10.1111/jopr.13755
BibTeX
@article{akmak2024,
author = {Çakmak, Gülce and Hess, Julia Anouk and Dönmez, Mustafa Borga and Yılmaz, Deniz and Alhotan, Abdulaziz and Schimmel, Martin and Peutzfeldt, Anne and Yilmaz, Burak},
title = {Effect of polishing and denture cleansers on the surface roughness of new‐generation denture base materials and their color change after cleansing},
journal = {Journal of Prosthodontics},
year = {2024},
volume = {33},
number = {8},
pages = {783--790},
doi = {10.1111/jopr.13755}
}
EUVIMED