EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Shear Bond Strength Between Artificial Teeth and Denture Base Resins Fabricated by Conventional, Milled, and 3D-Printed Workflows: An In Vitro Study

Giulia Verniani iD, Fatemeh Namdar, Ovidiu Ionut Saracutu, Alessio Casucci, Marco Ferrari iD

Materials · 03.10.2025 · 18 (19) · 4590

DOI: 10.3390/ma18194590 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 03.10.2025. Verfasst von Giulia Verniani und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, University of Siena, 53100 Siena, Italy. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 26 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Background

The adhesion between artificial teeth and denture bases is crucial for the longevity of complete dentures. This in vitro study evaluated the shear bond strength (SBS) and failure modes between artificial teeth and denture base resins produced with conventional, milled, and 3D-printed techniques. Materials: A total of 105 specimens were fabricated and assigned to 7 groups (n = 15) combining conventional, milled, or printed denture bases with conventional, milled, or printed teeth. SBS was tested using a universal testing machine, and failure modes were classified as adhesive, cohesive, or mixed. Data were analyzed with one-way ANOVA and Tukey’s post hoc test (α = 0.05).

Results

SBS significantly varied among groups (p < 0.001). The conventional base–conventional tooth group (CB-CT) showed the highest bond strength (14.9 ± 3.69 MPa), while the printed base–milled tooth group (PB-MT) had the lowest (6.58 ± 3.41 MPa). Milled base groups showed intermediate values (11.7–12.4 MPa).

Conclusions

Bond strength between denture teeth and denture bases depends on the fabrication workflow. Conventional heat-cured PMMA bases exhibited the most reliable adhesion, while milled bases demonstrated satisfactory performance with optimized bonding. Printed bases showed reduced and variable adhesion, suggesting the need for improved bonding protocols before their widespread clinical application in definitive prostheses.

Schlagwörter

Stichwörter der Autor:innen

3D printingcomplete denturedigital dentistrydigital workflow

Autor:innen und Institutionen

  • Department of Prosthodontics, University of Siena, 53100 Siena, Italy.
  • Department of Medical Biotechnologies, Division of TMJ and Oral Pain, University of Siena, 53100 Siena, Italy.
  • Division of Gerodontology and Removable Prosthodontics, University Clinics of Dental Medicine, University of Geneva, 1205 Geneva, Switzerland.

ORCID-Profile: Giulia Verniani, Marco Ferrari

Zitieren

APA

Verniani, G., Namdar, F., Saracutu, O. I., Casucci, A., & Ferrari, M. (2025). Shear Bond Strength Between Artificial Teeth and Denture Base Resins Fabricated by Conventional, Milled, and 3D-Printed Workflows: An In Vitro Study. Materials, 18(19), 4590. https://doi.org/10.3390/ma18194590

Vancouver

Verniani G, Namdar F, Saracutu OI, Casucci A, Ferrari M. Shear Bond Strength Between Artificial Teeth and Denture Base Resins Fabricated by Conventional, Milled, and 3D-Printed Workflows: An In Vitro Study. Materials. 2025;18(19):4590. doi:10.3390/ma18194590

BibTeX
@article{Verniani2025,
  author = {Verniani, Giulia and Namdar, Fatemeh and Saracutu, Ovidiu Ionut and Casucci, Alessio and Ferrari, Marco},
  title = {Shear Bond Strength Between Artificial Teeth and Denture Base Resins Fabricated by Conventional, Milled, and 3D-Printed Workflows: An In Vitro Study},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {19},
  pages = {4590},
  doi = {10.3390/ma18194590}
}
Kostenlos starten →