EUVIMEDEUVIMED entdecken
Crossref

Evaluation of Shear Bond Strength Between Denture Teeth and 3D‐Printed Denture Base Resin

Marília P Cleto, Marcela D D Silva, Thaís S B S Nunes, Hamile E C Viotto, Sabrina R G Coelho, Ana C Pero iD

Journal of Prosthodontics · 2023-04 · 32 (S1) · 3-10

DOI: 10.1111/jopr.13527 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, online erschienen am 16.06.2022. Verfasst von Marília P Cleto und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Dental Materials and Prosthodontics, Araraquara Dental School, Univ Estadual Paulista (UNESP), Araraquara, São Paulo, Brazil. Hauptthemen laut MEDLINE: Denture Bases, Dental Bonding. Die Arbeit wurde bisher 39-mal zitiert (Crossref) und nennt 38 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

The aim of this study was to evaluate the bond strength between two types of artificial teeth with a 3D‐printed denture base resin using different bonding agents. Materials and methods Two types of artificial teeth were evaluated: 3D‐printed (Cosmos TEMP) and prefabricated polymethylmethacrylate (Biotone) bonded to cylinders (2.5 mm in height and 5 mm in diameter) of 3D‐printed denture bases (Cosmos Denture designing by Meshmixer and printed by Flashforge Hunter DLP Resin 3D Printer). Two combinations between denture base and artificial teeth were eveluated: Cosmos Denture – Biotone, n = 30, and Cosmos Denture ‐ Cosmos TEMP, n = 30. For each combination, the specimens were randomly distributed according to the bonding agent: (1) autopolymerized acrylic resin‐Duralay, n = 10; (2) 3D‐printed resin Cosmos TEMP, n = 10; and (3) methylmethacrylate monomer (MMA) + 3D‐printed resin Cosmos TEMP, n = 10, totaling 60 specimens. The application of MMA was done conditioning the tooth surface for 180 seconds; the other agents were applied on the same surface. The virtual design of the 3D‐printed resin teeth was obtained by scanning the first maxillary molar of the prefabricated teeth as the same protocol of cylinders. The control group (n = 10) was a conventional heat‐polymerized denture base resin (Lucitone 550) bonded to the prefabricated resin teeth (Biotone). The shear bond tests were performed by applying a perpendicular force to the artificial tooth – denture base resin, through a chisel at 1 mm/min until failure. Two‐way ANOVA and Bonferroni post hoc tests (α = 0.05) were used for multiple comparisons.

Results

For the Biotone tooth, the bond strength was significantly higher using MMA + Cosmos TEMP (10.04 MPa), and similar to the control (11.84 MPa, p = 0.484). For the 3D‐printed tooth (Cosmos TEMP), the bond strength using the agents Cosmos TEMP (9.57 MPa) and MMA + Cosmos TEMP (12.72 MPa) were similar to the control (11.84 MPa, p = 0.169 and p = 1, respectively), but different from each other ( p = 0.016).

Conclusions

From the results, it is recommended to use: MMA + Cosmos TEMP bonding agent for the Biotone tooth; and Cosmos TEMP or MMA + Cosmos TEMP bonding agents for the Cosmos TEMP tooth, both attached to the 3D‐printed denture resin Cosmos Denture.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Denture BasesDental BondingTooth, ArtificialPolymethyl MethacrylateMethylmethacrylatePrinting, Three-DimensionalMaterials TestingSurface PropertiesShear Strength

Stichwörter der Autor:innen

3D-printingacrylic resinsartificialcomplete denturedenture basestooth

Substanzen

Polymethyl MethacrylateMethylmethacrylate

Autor:innen und Institutionen

  • Department of Dental Materials and Prosthodontics, Araraquara Dental School, Univ Estadual Paulista (UNESP), Araraquara, São Paulo, Brazil.

ORCID-Profile: Ana C Pero

Zitieren

APA

Cleto, M. P., Silva, M. D. D., Nunes, T. S. B. S., Viotto, H. E. C., Coelho, S. R. G., & Pero, A. C. (2023). Evaluation of Shear Bond Strength Between Denture Teeth and 3D‐Printed Denture Base Resin. Journal of Prosthodontics, 32(S1), 3-10. https://doi.org/10.1111/jopr.13527

Vancouver

Cleto MP, Silva MDD, Nunes TSBS, Viotto HEC, Coelho SRG, Pero AC. Evaluation of Shear Bond Strength Between Denture Teeth and 3D‐Printed Denture Base Resin. Journal of Prosthodontics. 2023;32(S1):3-10. doi:10.1111/jopr.13527

BibTeX
@article{Cleto2023,
  author = {Cleto, Marília P and Silva, Marcela D D and Nunes, Thaís S B S and Viotto, Hamile E C and Coelho, Sabrina R G and Pero, Ana C},
  title = {Evaluation of Shear Bond Strength Between Denture Teeth and 3D‐Printed Denture Base Resin},
  journal = {Journal of Prosthodontics},
  year = {2023},
  volume = {32},
  number = {S1},
  pages = {3--10},
  doi = {10.1111/jopr.13527}
}
Kostenlos starten →