A comparison of the shear bond strength between denture teeth and denture base resins manufactured either conventionally or with a 3D printer
The Journal of Prosthetic Dentistry · 2023-11 · 130 (5) · 742.e1-742.e6
DOI: 10.1016/j.prosdent.2023.08.035 ↗Kurz gefasst
Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2023-11. Verfasst von Nazli Aydin und 3 weiteren Autor:innen. Beteiligte Einrichtung: Lecturer, Cukurova University, Faculty of Dentistry, Department of Prosthodontics, Adana, Turkey; and Abdi Sutcu Vocational School of Health Services…. Hauptthemen laut MEDLINE: Acrylic Resins, Dental Bonding. Die Arbeit wurde bisher 18-mal zitiert (Crossref) und nennt 30 Literaturangaben.
Abstract (Originalsprache)
STATEMENT OF PROBLEM: Limited information is available on the shear bond strength (SBS) between denture teeth and denture base resins fabricated using a stereolithography (SLA) 3-dimensional (3D) printer. PURPOSE: The purpose of this in vitro study was to evaluate the SBS between denture teeth and the denture base resins produced with the conventional method and with a 3D printer. MATERIAL AND METHODS: Conventional or 3D printed denture teeth were included in the study. The denture base resins were manufactured either conventionally or with a 3D printer. Four subgroups were tested: conventional teeth-conventional base resin (CT-CB), conventional teeth-printed base resin (CT-PB), printed teeth-conventional base resin (PT-CB), and printed teeth-printed base resin (PT-PB). The maxillary molars were combined with Ø5×2.5-mm-cylindrical denture base resin. Shear bond testing was performed by applying a parallel force to the denture teeth-denture base resin interface by using a blade-edge chisel with a crosshead speed of 1 mm/min until failure occurred. SBS and elastic modulus (EM) were recorded. One-way ANOVA followed by the Dunnett T3 post hoc test was used for the statistical analysis (α=.05). The failure modes of the specimens were also analyzed. RESULTS: A statistically significant difference (P
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Substanzen
Autor:innen und Institutionen
- Lecturer, Cukurova University, Faculty of Dentistry, Department of Prosthodontics, Adana, Turkey; and Abdi Sutcu Vocational School of Health Services, Cukurova University, Balcali, Adana, Turkey. Electronic address: naz…
- Private practice, Antalya, Turkey.
- R&D and Product Manager, SINERG Lokman Hekim University, Ankara, Turkey.
Zitieren
APA
Aydin, N., Uslu Kavrama, F., Yosuncigir, H., & Ucar, Y. (2023). A comparison of the shear bond strength between denture teeth and denture base resins manufactured either conventionally or with a 3D printer. The Journal of Prosthetic Dentistry, 130(5), 742.e1-742.e6. https://doi.org/10.1016/j.prosdent.2023.08.035
Vancouver
Aydin N, Uslu Kavrama F, Yosuncigir H, Ucar Y. A comparison of the shear bond strength between denture teeth and denture base resins manufactured either conventionally or with a 3D printer. The Journal of Prosthetic Dentistry. 2023;130(5):742.e1-742.e6. doi:10.1016/j.prosdent.2023.08.035
BibTeX
@article{Aydin2023,
author = {Aydin, Nazli and Uslu Kavrama, Fatma and Yosuncigir, Halit and Ucar, Yurdanur},
title = {A comparison of the shear bond strength between denture teeth and denture base resins manufactured either conventionally or with a 3D printer},
journal = {The Journal of Prosthetic Dentistry},
year = {2023},
volume = {130},
number = {5},
pages = {742.e1--742.e6},
doi = {10.1016/j.prosdent.2023.08.035}
}
EUVIMED