EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Experimental study of the process of thermal friction milling of HARDOX 450 steel and modeling of the temperature in the cutting zone

Karibek Sherov, Issa Kuanov, Bakytzhan Donenbayev, Aibek Sherov, Medgat Mussayev, Sayagul Tussupova, Saule Ainabekova, Abay Bobeev, Gulzada Tazhenova

Frontiers in Mechanical Engineering · 21.08.2026 · 12

DOI: 10.3389/fmech.2026.1835202 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Frontiers in Mechanical Engineering, online erschienen am 21.08.2026. Verfasst von Karibek Sherov und 8 weiteren Autor:innen. Die Arbeit nennt 25 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Introduction

This study investigates the influence of cutting conditions on the quality of the machined surface during thermal friction milling with pulsed cooling of HARDOX 450 steel.

Methods

Experiments were conducted by varying the friction-cutter rotational speed, feed rate, and cutting depth. Surface roughness and hardness were measured after machining. A simplified ANSYS Workbench model consisting of a HARDOX 450 workpiece and a plate representing the cutting edge was used to estimate contact temperatures at nine characteristic points.

Results

The process provided a surface roughness of Ra = 1.0−7.5 μm. The hardness of the machined surface did not decrease below the characteristic range of HARDOX 450 and could be controlled through the cutting conditions. The rational conditions were n = 2800 rpm, S = 60 mm/min, and t = 2 mm. Numerical results showed a nonuniform temperature field and local heat accumulation near the final part of the contact trajectory.

Discussion

Thermal friction milling with pulsed cooling can provide controlled surface quality while preserving surface hardness. The numerical temperature values should be regarded as computational estimates; further experimental temperature validation and microstructural analysis are required.

Zitieren

APA

Sherov, K., Kuanov, I., Donenbayev, B., Sherov, A., Mussayev, M., Tussupova, S., Ainabekova, S., Bobeev, A., & Tazhenova, G. (2026). Experimental study of the process of thermal friction milling of HARDOX 450 steel and modeling of the temperature in the cutting zone. Frontiers in Mechanical Engineering, 12. https://doi.org/10.3389/fmech.2026.1835202

Vancouver

Sherov K, Kuanov I, Donenbayev B, Sherov A, Mussayev M, Tussupova S, et al. Experimental study of the process of thermal friction milling of HARDOX 450 steel and modeling of the temperature in the cutting zone. Frontiers in Mechanical Engineering. 2026;12. doi:10.3389/fmech.2026.1835202

BibTeX
@article{Sherov2026,
  author = {Sherov, Karibek and Kuanov, Issa and Donenbayev, Bakytzhan and Sherov, Aibek and Mussayev, Medgat and Tussupova, Sayagul and Ainabekova, Saule and Bobeev, Abay and Tazhenova, Gulzada},
  title = {Experimental study of the process of thermal friction milling of HARDOX 450 steel and modeling of the temperature in the cutting zone},
  journal = {Frontiers in Mechanical Engineering},
  year = {2026},
  volume = {12},
  doi = {10.3389/fmech.2026.1835202}
}
Kostenlos starten →