EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Adjustment of CAD–CAM crowns with and without a 3D‐printed model: Comparative study of marginal fit

Marwan Al Akkad iD, Bedirhan Savas Yigit iD, Iva Voborna iD, Vaclav Prokupek iD, Oluwafunmibi Fasanya iD, Thomas Salinas iD, Radek Mounajjed iD

Journal of Prosthodontics · 09.07.2026

DOI: 10.1111/jopr.70190 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, online erschienen am 09.07.2026. Verfasst von Marwan Al Akkad und 6 weiteren Autor:innen. Beteiligte Einrichtung: Institute of Dentistry and Oral Sciences, Faculty of Medicine and Dentistry, Palacký University Olomouc, Olomouc, Czech Republic. Die Arbeit nennt 36 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Palacký University Olomouc, Univerzita Palackého v Olomouci.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

This study evaluated and compared the marginal fit of CAD–CAM zirconia crown copings with and without a 3D‐printed control model. Materials and Methods This prospective in vitro trial involved 30 zirconia crown copings made from the same STL file. These were divided into two groups. Half of them had their own 3D‐printed control model made from the same STL file (With‐Printed‐Model group), whereas the other half lacked any control model (No‐Printed‐Model group). Both groups underwent manual adjustments in a systematic way. Their marginal gaps were evaluated using a digital optical microscope from eight zones: buccal, mesiobuccal, mesial, mesiopalatal, palatal, distopalatal, distal, and distobuccal.

Results

The mean values with standard deviations for the With‐Printed‐Model and No‐Printed‐Model groups were 15.18 ± 14.49 and 12.46 ± 14.09 µm, respectively. All crown copings from both groups were below 75 µm. Statistical analysis showed a significant difference between the two groups.

Conclusion

The No‐Printed‐Model group demonstrated superior marginal fit compared to the With‐Printed‐Model group. However, the largest marginal gaps from each group were still within the clinically acceptable range below 75 µm. Although the 3D‐printed control model did not improve marginal fit, its primary function is to effectively identify major manufacturing errors.

Schlagwörter

Stichwörter der Autor:innen

3D printingCAD–CAMceramicsdental crownsdental marginal adaptationdental prosthesis designmicroscopyprosthodonticszirconia

Autor:innen und Institutionen

  • Institute of Dentistry and Oral Sciences, Faculty of Medicine and Dentistry, Palacký University Olomouc, Olomouc, Czech Republic.
  • D.C.M Clinic, Hradec Kralove, Czech Republic.
  • Dental Clinic of Faculty Hospital in Olomouc, Palacký University Olomouc, Olomouc, Czech Republic.
  • Department of Experimental Physics, Faculty of Science, Palacký University Olomouc, Olomouc, Czech Republic.
  • Department of Biostatistics and Data Science, School of Public Health, Louisiana State University Health Sciences Center, New Orleans, Louisiana, USA.
  • Department of Dental Specialties, Mayo Clinic College of Medicine and Science, Rochester, Minnesota, USA.

ORCID-Profile: Marwan Al Akkad, Bedirhan Savas Yigit, Iva Voborna, Vaclav Prokupek, Oluwafunmibi Fasanya, Thomas Salinas, Radek Mounajjed

Förderung

  • Palacký University Olomouc
  • Univerzita Palackého v Olomouci

Zitieren

APA

Al Akkad, M., Yigit, B. S., Voborna, I., Prokupek, V., Fasanya, O., Salinas, T., & Mounajjed, R. (2026). Adjustment of CAD–CAM crowns with and without a 3D‐printed model: Comparative study of marginal fit. Journal of Prosthodontics. https://doi.org/10.1111/jopr.70190

Vancouver

Al Akkad M, Yigit BS, Voborna I, Prokupek V, Fasanya O, Salinas T, et al. Adjustment of CAD–CAM crowns with and without a 3D‐printed model: Comparative study of marginal fit. Journal of Prosthodontics. 2026. doi:10.1111/jopr.70190

BibTeX
@article{AlAkkad2026,
  author = {Al Akkad, Marwan and Yigit, Bedirhan Savas and Voborna, Iva and Prokupek, Vaclav and Fasanya, Oluwafunmibi and Salinas, Thomas and Mounajjed, Radek},
  title = {Adjustment of CAD–CAM crowns with and without a 3D‐printed model: Comparative study of marginal fit},
  journal = {Journal of Prosthodontics},
  year = {2026},
  doi = {10.1111/jopr.70190}
}
Kostenlos starten →