EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

The Influence of Material and Veneering Technique on the Marginal Fit of CAD/CAM Crowns

Nader Abdulhameed iD, Jean Francois Roulet, Hind Hussein iD, Zahraa Mahdi, Noor Ibrahim, Taiseer Sulaiman iD, Emmanouil-George Tzanakakis iD, Panagiotis Zoidis iD

Dentistry Journal · 01.07.2026 · 14 (7) · 397

DOI: 10.3390/dj14070397 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Dentistry Journal, online erschienen am 01.07.2026. Verfasst von Nader Abdulhameed und 7 weiteren Autor:innen. Beteiligte Einrichtung: Restorative Dental Sciences, College of Dentistry, University of Florida, Gainesville, FL 32610, USA. Die Arbeit nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Background

There are certain disadvantages to using CAD/CAM technologies. Marginal and internal accuracy of fit is valued as one of the most important criteria for the clinical quality and success of all-ceramic crowns. The assessment of the marginal fit of lithium disilicate and zirconia CAD/CAM crowns before and after ceramic layering is crucial.

Methods

One ideally prepared model tooth was duplicated into 64 plaster models. A standardized wax pattern for a monolithic crown and a coping were produced and used to mill 16 lithium disilicate monolithic crowns and 16 cores using a soft milling process. 16 zirconia crowns and 16 cores were also fabricated. A factorial design with (material) (lithium disilicate [E] or zirconia [Z]); (design) (monolithic, [M] or (core) [C]); and (finish) (as-produced [P] or veneered/glazed [G]) was used to create the following groups: ZMP, ZMG, ZCP, ZCG, EMP, EMG, ECP, and ECG (n = 8). The milled restorations were treated accordingly using ZirLiner, IPS e.max Ceram, and IPS e.max Glaze. The restorations were cemented to their dies, embedded in epoxy resin, and sectioned into two planes with a diamond saw. Vertical and horizontal marginal fit at the finishing line was measured in a standardized way at four locations (mesial, distal, facial, and lingual).

Results

There were no differences, p > 0.05, between all Z groups; however, they had significantly wider horizontal gaps, p < 0.05, (116 ± 5 µm) than E groups (64 ± 13 µm). Among lithium disilicate groups, the glazed monolithic (EMG) and veneered/glazed coping (ECG) subgroups showed significantly smaller horizontal gaps (approximately 50 ± 6 µm). Statistical analysis was performed using two-way ANOVA with a significance level set at α = 0.05.

Conclusions

Veneering techniques did not affect zirconia. Lithium disilicate had a better marginal fit than zirconia, but this was influenced by veneering techniques. Lithium disilicate veneering and/or glazing significantly improved the marginal fit.

Schlagwörter

Stichwörter der Autor:innen

CAD-CAMglazinglithium disilicatemarginal fitveneeringzirconia

Autor:innen und Institutionen

  • Restorative Dental Sciences, College of Dentistry, University of Florida, Gainesville, FL 32610, USA.
  • Independent Dental Research Group, Chicago, IL 60563, USA.
  • Division of Comprehensive Oral Health, University of North Carolina, Chapel Hill, NC 27599, USA.
  • Department of Dentistry, School of Dentistry, European University Cyprus, 1516 Nicosia, Cyprus.

ORCID-Profile: Nader Abdulhameed, Hind Hussein, Taiseer Sulaiman, Emmanouil-George Tzanakakis, Panagiotis Zoidis

Zitieren

APA

Abdulhameed, N., Roulet, J. F., Hussein, H., Mahdi, Z., Ibrahim, N., Sulaiman, T., Tzanakakis, E. G., & Zoidis, P. (2026). The Influence of Material and Veneering Technique on the Marginal Fit of CAD/CAM Crowns. Dentistry Journal, 14(7), 397. https://doi.org/10.3390/dj14070397

Vancouver

Abdulhameed N, Roulet JF, Hussein H, Mahdi Z, Ibrahim N, Sulaiman T, et al. The Influence of Material and Veneering Technique on the Marginal Fit of CAD/CAM Crowns. Dentistry Journal. 2026;14(7):397. doi:10.3390/dj14070397

BibTeX
@article{Abdulhameed2026,
  author = {Abdulhameed, Nader and Roulet, Jean Francois and Hussein, Hind and Mahdi, Zahraa and Ibrahim, Noor and Sulaiman, Taiseer and Tzanakakis, Emmanouil-George and Zoidis, Panagiotis},
  title = {The Influence of Material and Veneering Technique on the Marginal Fit of CAD/CAM Crowns},
  journal = {Dentistry Journal},
  year = {2026},
  volume = {14},
  number = {7},
  pages = {397},
  doi = {10.3390/dj14070397}
}
Kostenlos starten →