EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Comparative Analysis between Conventional Acrylic, CAD/CAM Milled, and 3D CAD/CAM Printed Occlusal Splints

Cristian Abad-Coronel iD, Carolina Ruano Espinosa, Sofía Ordóñez Palacios, César A Paltán iD, Jorge I Fajardo iD

Materials · 19.09.2023 · 16 (18) · 6269

DOI: 10.3390/ma16186269 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 19.09.2023. Verfasst von Cristian Abad-Coronel und 4 weiteren Autor:innen. Beteiligte Einrichtung: CAD/CAM Materials and Digital Dentistry Research Group, Faculty of Dentistry, Universidad de Cuenca, Cuenca 010204, Ecuador. Die Arbeit wurde bisher 30-mal zitiert (Crossref) und nennt 33 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The development of digital technologies has allowed for the fabrication of new materials; however, it makes it difficult to choose the best methods to obtain occlusal splints with optimal properties, so it is essential to evaluate the effectiveness of these materials. The aim of the study is to compare the fracture resistance of occlusal splints made of different materials after thermo-mechanical aging.

Methods

A total of 32 samples were made from 4 materials (two 3D printed polymeric materials, a PMMA disc for CAD/CAM, and a conventional heat-cured acrylic resin); subsequently, the fracture test was performed using the load compression mode applied occlusally on the splint surface. Statistical analysis: Four statistical tests were used (Shapiro-Wilk, Levene’s test, ANOVA, and Tukey’s HSD test).

Results

The following study showed that there are differences in fracture strength among the four materials investigated, where the highest strength was observed in the milled splint, with a mean of 3051.2 N (newton) compared to the strength of the flexible splint with 1943.4 N, the printed splint with 1489.9 N, and the conventional acrylic splint with 1303.9 N.

Conclusions

The milled splints were the most resistant to fracture. Of the printed splints, the splint made with flexural rigid resin withstood the applied forces in acceptable ranges, so its clinical indication may be viable. Although the results of this research indicated differences in the mechanical properties between the CAD/CAM and conventional fabrication methods, the selection may also be influenced by processing time and cost, since with a CAD/CAM system there is a significant reduction in the production time of the splint material.

Schlagwörter

Stichwörter der Autor:innen

3D printingCAD/CAM materialsdigital dentistryfracture resistanceocclusal splint

Autor:innen und Institutionen

  • CAD/CAM Materials and Digital Dentistry Research Group, Faculty of Dentistry, Universidad de Cuenca, Cuenca 010204, Ecuador.
  • Faculty of Dentistry, Universidad de Cuenca, Cuenca 010204, Ecuador.
  • New Materials and Transformation Processes Research Group GiMaT, Universidad Politécnica Salesiana, Cuenca 010105, Ecuador.

ORCID-Profile: Cristian Abad-Coronel, César A Paltán, Jorge I Fajardo

Zitieren

APA

Abad-Coronel, C., Ruano Espinosa, C., Ordóñez Palacios, S., Paltán, C. A., & Fajardo, J. I. (2023). Comparative Analysis between Conventional Acrylic, CAD/CAM Milled, and 3D CAD/CAM Printed Occlusal Splints. Materials, 16(18), 6269. https://doi.org/10.3390/ma16186269

Vancouver

Abad-Coronel C, Ruano Espinosa C, Ordóñez Palacios S, Paltán CA, Fajardo JI. Comparative Analysis between Conventional Acrylic, CAD/CAM Milled, and 3D CAD/CAM Printed Occlusal Splints. Materials. 2023;16(18):6269. doi:10.3390/ma16186269

BibTeX
@article{AbadCoronel2023,
  author = {Abad-Coronel, Cristian and Ruano Espinosa, Carolina and Ordóñez Palacios, Sofía and Paltán, César A and Fajardo, Jorge I},
  title = {Comparative Analysis between Conventional Acrylic, CAD/CAM Milled, and 3D CAD/CAM Printed Occlusal Splints},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {18},
  pages = {6269},
  doi = {10.3390/ma16186269}
}
Kostenlos starten →