EUVIMEDEUVIMED entdecken
VergleichsstudieOpen Access

In vitro comparison of physical characteristics of milled versus printed zirconia discs

Thomas S Giugliano iD, Yu Zhang, Malvin N Janal, Chek Hai Lim, Ruby M Smith, Mijin Choi iD

Journal of Prosthodontics · 2024-12 · 33 (9) · 891-898

DOI: 10.1111/jopr.13778 ↗

Kurz gefasst

Vergleichsstudie in der Zeitschrift Journal of Prosthodontics, 2023-11. Verfasst von Thomas S Giugliano und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, New York University College of Dentistry, New York, New York, USA. Hauptthemen laut MEDLINE: Zirconium, Printing, Three-Dimensional, Computer-Aided Design, Materials Testing. Die Arbeit wurde bisher 18-mal zitiert (Crossref) und nennt 36 Literaturangaben. Der Volltext ist frei in PubMed Central verfügbar. Gefördert von: NIDCR NIH HHS, National Institutes of Health/National Institute of Dental and Craniofacial Research.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

The purpose of this study was to compare the dimensional accuracy, translucency, and biaxial flexural strength of milled zirconia (MZ) versus 3D‐printed zirconia (PZ) discs. Materials & Methods A circular disc measuring 14.0 mm in diameter and 1.20 mm in thickness was designed using computer‐aided design (CAD) software. The resulting standard tessellation language (STL) file was used both as a control and to fabricate 36 zirconia (3Y‐TZP) disc specimens ( n = 36): 18 were milled (group MZ) and 18 were 3D‐printed (group PZ). The diameter and thickness of each disc were measured using a digital caliper. Translucency was evaluated using a calibrated dental colorimeter. The flexural strength was determined using the piston‐on‐three‐ball biaxial flexure test. All measurements were done by one blinded examiner. The statistical significance level was set to α = 0.05.

Results

The MZ discs had significantly more accurate dimensions than the PZ discs in both diameter and thickness when compared to the control CAD software‐designed disc. The MZ discs exhibited significantly higher translucency (translucency parameter (TP) = 16.95 ±0.36 vs. 9.24 ±1.98) and biaxial flexural strength (996.16 ±137.37 MPa vs. 845.75 ±266.16 MPa) than the PZ discs. Finally, MZ possessed a significantly higher Weibull modulus relative to PZ.

Conclusions

The results showed that the milled specimens achieved better dimensional accuracy and were more translucent, stronger, and less prone to failure than printed specimens.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

ZirconiumPrinting, Three-DimensionalComputer-Aided DesignMaterials TestingFlexural StrengthHumansDental MaterialsIn Vitro TechniquesDental Stress AnalysisDental Prosthesis DesignSurface Properties

Stichwörter der Autor:innen

3D‐printed zirconia3Y‐TZPadditive manufacturingmilled zirconiasubtractive manufacturing

Substanzen

Zirconiumzirconium oxideDental Materials

Autor:innen und Institutionen

  • Department of Prosthodontics, New York University College of Dentistry, New York, New York, USA.
  • Laboratories for Microstructure Physics & Mechanics of Materials, Department of Preventive and Restorative Sciences, School of Dental Medicine, University of Pennsylvania, Philadelphia, Pennsylvania, USA.
  • Department of Epidemiology & Health Promotion, New York University College of Dentistry, New York, New York, USA.

ORCID-Profile: Thomas S Giugliano, Mijin Choi

Förderung

  • NIDCR NIH HHS
  • National Institutes of Health/National Institute of Dental and Craniofacial Research

Zitieren

APA

Giugliano, T. S., Zhang, Y., Janal, M. N., Lim, C. H., Smith, R. M., & Choi, M. (2024). In vitro comparison of physical characteristics of milled versus printed zirconia discs. Journal of Prosthodontics, 33(9), 891-898. https://doi.org/10.1111/jopr.13778

Vancouver

Giugliano TS, Zhang Y, Janal MN, Lim CH, Smith RM, Choi M. In vitro comparison of physical characteristics of milled versus printed zirconia discs. Journal of Prosthodontics. 2024;33(9):891-898. doi:10.1111/jopr.13778

BibTeX
@article{Giugliano2024,
  author = {Giugliano, Thomas S and Zhang, Yu and Janal, Malvin N and Lim, Chek Hai and Smith, Ruby M and Choi, Mijin},
  title = {In vitro comparison of physical characteristics of milled versus printed zirconia discs},
  journal = {Journal of Prosthodontics},
  year = {2024},
  volume = {33},
  number = {9},
  pages = {891--898},
  doi = {10.1111/jopr.13778}
}
Kostenlos starten →