EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Wear behavior of CAD-CAM zirconia, ceramic, and 3D printed nano-hybrid resin crowns for the restoration of primary and permanent molars: An in vitro study

Behrang Ghabchi, Fırat Mavi, Erhan Çömlekoğlu, Ibrahim Etem Saklakoğlu, Ilhan Uzel

The Journal of Prosthetic Dentistry · 2025-07 · 134 (1) · 177.e1-177.e8

DOI: 10.1016/j.prosdent.2025.02.040 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2025-07. Verfasst von Behrang Ghabchi und 4 weiteren Autor:innen. Beteiligte Einrichtung: PhD candidate, Department of Pedodontics, School of Dentistry, Ege University, Izmir, Turkey. Hauptthemen laut MEDLINE: Crowns, Zirconium, Ceramics, Molar. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 41 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: Early childhood caries is one the world's most common problems in infants and treatment of posterior teeth with esthetic crowns in a low rate of wear on opposite dentition is a challenge for pediatric dentists. PURPOSE: The purpose of this in vitro study was to evaluate the wear behavior of the tooth colored crown materials and the opposing teeth in using different esthetic crown materials in the mixed dentition period. MATERIAL AND METHODS: The following tooth type and crown materials were considered in the experiment. Primary molars consist of first and second molars that were close to exfoliation or needed to be extracted because of orthodontic treatment and were caries free and with no restorations. Permanent teeth consisted of third molars that were caries free and with no restorations. Three different types of crown materials were used: nano-hybrid resin (VarseoSmile Crown plus; Bego GmbH), tetragonal zirconia polycrystalline stabilized with 3 mol% yttria (G-CERAM; Atlas Enta), and lithium disilicate glass-ceramic (IPS e.max CAD; Ivoclar AG). The wear test was performed in an artificial saliva environment (pH=6.7), based on the pin-on-plate technique, for a 2-mm stroke, under a compressive force of 30-N, at a frequency of 2-Hz and with 10 000, 20 000, and 30 000 cycles. A multi-way ANOVA statistical method was used (α=.05). RESULTS: Wear of the opposing teeth by the glass-ceramic was greater than by the nano-hybrid resin or zirconia materials (P

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

CrownsZirconiumCeramicsMolarComputer-Aided DesignPrinting, Three-DimensionalDental Restoration WearHumansTooth, DeciduousIn Vitro TechniquesDental PorcelainDental MaterialsMaterials TestingDental Restoration, Permanent

Substanzen

Zirconiumzirconium oxideDental PorcelainDental Materialslithia disilicate

Autor:innen und Institutionen

  • PhD candidate, Department of Pedodontics, School of Dentistry, Ege University, Izmir, Turkey.
  • PhD candidate, Department of Mechanical Engineering, Faculty of Engineering, Ege University, Izmir, Turkey.
  • Professor, Department of Prosthodontics, School of Dentistry, Ege University, Izmir, Turkey.
  • Professor, Department of Mechanical Engineering, Faculty of Engineering, Ege University, Izmir, Turkey.
  • Associate Professor, Department of Pedodontics, School of Dentistry, Ege University, Izmir, Turkey. Electronic address: uzel_ilhan@hotmail.com.

Zitieren

APA

Ghabchi, B., Mavi, F., Çömlekoğlu, E., Saklakoğlu, I. E., & Uzel, I. (2025). Wear behavior of CAD-CAM zirconia, ceramic, and 3D printed nano-hybrid resin crowns for the restoration of primary and permanent molars: An in vitro study. The Journal of Prosthetic Dentistry, 134(1), 177.e1-177.e8. https://doi.org/10.1016/j.prosdent.2025.02.040

Vancouver

Ghabchi B, Mavi F, Çömlekoğlu E, Saklakoğlu IE, Uzel I. Wear behavior of CAD-CAM zirconia, ceramic, and 3D printed nano-hybrid resin crowns for the restoration of primary and permanent molars: An in vitro study. The Journal of Prosthetic Dentistry. 2025;134(1):177.e1-177.e8. doi:10.1016/j.prosdent.2025.02.040

BibTeX
@article{Ghabchi2025,
  author = {Ghabchi, Behrang and Mavi, Fırat and Çömlekoğlu, Erhan and Saklakoğlu, Ibrahim Etem and Uzel, Ilhan},
  title = {Wear behavior of CAD-CAM zirconia, ceramic, and 3D printed nano-hybrid resin crowns for the restoration of primary and permanent molars: An in vitro study},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2025},
  volume = {134},
  number = {1},
  pages = {177.e1--177.e8},
  doi = {10.1016/j.prosdent.2025.02.040}
}
Kostenlos starten →