EUVIMEDEUVIMED entdecken
Crossref

Assessment of mechanical properties and microstructure of Co-Cr dental alloys manufactured by casting, milling, and 3D printing

Ana Schettini, Igor J Pesun, Rodrigo França

The Journal of Prosthetic Dentistry · 2025

DOI: 10.1016/j.prosdent.2024.12.017 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2025. Verfasst von Ana Schettini und 2 weiteren Autor:innen. Beteiligte Einrichtung: Graduate student, Graduate Prosthodontics, Department of Restorative Dentistry, Gerald Niznick College of Dentistry, University of Manitoba, Winnipeg…. Hauptthemen laut MEDLINE: Chromium Alloys, Printing, Three-Dimensional, Dental Casting Technique, Dental Alloys. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 40 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: The mechanical properties and microstructure of cobalt chromium (Co-Cr) alloys should be considered when choosing the best alloy for each clinical situation. More information is needed on the digital manufacturing methods of metals in dentistry, such as computer numerical control (CNC), and direct laser metal sintering (DMLS). PURPOSE: The aim of this study was to investigate the effect of the 3 different Co-Cr manufacturing processes on the mechanical properties and microstructure of Co-Cr dental alloys. MATERIAL AND METHODS: Dumbbell-shaped specimens (n=6) were fabricated using casting (CAST), CNC, and DMLS techniques. Tensile, 3-point bend, and microhardness testing were performed, and the microstructure evaluated through scanning electron microscopy, energy dispersive X-ray analysis, and X-ray diffraction analysis. The ANOVA test followed by post hoc Tukey tests were used for statistical analysis (α=.05). RESULTS: DMLS showed the greatest values for 0.2% yield strength (908.0 ±13.1 MPa), tensile strength (1123.7 ±6.5 MPa), flexural strength (2273.0 ±43.2 MPa), and microhardness (438.2 ±44.9 HV), followed by CAST and CNC. No statistical differences were found for elongation between CNC and DMLS or DMLS and CAST (P>.05). No statistical differences were found in elastic modulus among all groups (P>.05). EDX revealed a slightly different chemical composition among the groups. XRD showed face-centered cubic as the dominant phase and a small amount of hexagonal close-packed structure in all groups. A peak of σ phase was identified in the CAST group. CONCLUSIONS: The mechanical properties and microstructures of Co-Cr dental alloys were significantly influenced by the fabrication method used. DMLS and CNC milling produced better products that traditional methods, leading to the improved durability and reliability of dental prostheses. These advancements underscore the importance of selecting appropriate fabrication methods to optimize clinical outcomes and patient satisfaction.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Chromium AlloysPrinting, Three-DimensionalDental Casting TechniqueDental AlloysMaterials TestingTensile StrengthHardnessMicroscopy, Electron, ScanningX-Ray DiffractionHumansFlexural Strength

Substanzen

Chromium AlloysDental Alloys

Autor:innen und Institutionen

  • Graduate student, Graduate Prosthodontics, Department of Restorative Dentistry, Gerald Niznick College of Dentistry, University of Manitoba, Winnipeg, Manitoba, Canada.
  • Associate Professor and Director, Graduate Prosthodontics, Department of Restorative Dentistry, Gerald Niznick College of Dentistry, University of Manitoba, Winnipeg, Manitoba, Canada.
  • Associate Professor, Dental Biomaterials Research Laboratory, Department of Restorative Dentistry, Gerald Niznick College of Dentistry, University of Manitoba, Winnipeg, Manitoba, Canada. Electronic address: rodrigo.fra…

Zitieren

APA

Schettini, A., Pesun, I. J., & França, R. (2025). Assessment of mechanical properties and microstructure of Co-Cr dental alloys manufactured by casting, milling, and 3D printing. The Journal of Prosthetic Dentistry. https://doi.org/10.1016/j.prosdent.2024.12.017

Vancouver

Schettini A, Pesun IJ, França R. Assessment of mechanical properties and microstructure of Co-Cr dental alloys manufactured by casting, milling, and 3D printing. The Journal of Prosthetic Dentistry. 2025. doi:10.1016/j.prosdent.2024.12.017

BibTeX
@article{Schettini2025,
  author = {Schettini, Ana and Pesun, Igor J and França, Rodrigo},
  title = {Assessment of mechanical properties and microstructure of Co-Cr dental alloys manufactured by casting, milling, and 3D printing},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2025},
  doi = {10.1016/j.prosdent.2024.12.017}
}
Kostenlos starten →