Influence of repeated porcelain firing cycles on the microstructure, marginal and internal fit of implant‐cemented Co‐Cr frameworks
European Journal of Oral Sciences · 2025
DOI: 10.1111/eos.70009 ↗Kurz gefasst
Fachartikel in der Zeitschrift European Journal of Oral Sciences, 2025. Verfasst von Michael Nikolopoulos und 4 weiteren Autor:innen. Beteiligte Einrichtung: Division of Dental Technology, Department of Biomedical Sciences, University of West Attica, Athens, Greece. Hauptthemen laut MEDLINE: Chromium Alloys, Dental Porcelain, Dental Marginal Adaptation, Dental Prosthesis, Implant-Supported. Die Arbeit nennt 65 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).
Abstract (Originalsprache)
This study investigated the effect of porcelain firing cycles and fabrication techniques on the microstructure, marginal, and internal fit of implant‐cemented cobalt‐chromium alloys (Co‐Cr) frameworks. Two groups of Co‐Cr specimens were prepared: one using selective laser melting (SLM) and the other through the lost wax‐casting technique (C). Each group was further divided into two subgroups: as‐manufactured and porcelain‐fired specimens. The microstructure was analyzed using x‐ray diffraction (XRD) and scanning electron microscopy with energy‐dispersive x‐ray spectroscopy (SEM/EDX). Ten Co‐Cr frameworks per manufacturing technique were fabricated, with marginal and internal discrepancies measured using micro‐CT before and after the firing cycles. The results were analyzed by two‐way ANOVA and Tukey multiple‐comparison tests. The results showed a mixed microstructure of γ‐fcc and ε‐hcp cobalt‐based phases, with porcelain firings increasing ε‐Co content, especially in group C. The C specimens exhibited distribution of small pores, while no pores/defects were found in the SLM group. The SLM group, although not at a statistically significant level, showed reduced marginal and internal discrepancy values after firings. In the same behavior pattern, the C group exhibited statistically significantly lower discrepancy values. Ultimately, all subgroups demonstrated clinically acceptable marginal adaptation, but the SLM frameworks exhibited superior marginal and internal fit which remained unaffected by the firing cycles.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Division of Dental Technology, Department of Biomedical Sciences, University of West Attica, Athens, Greece.
ORCID-Profile: Michael Nikolopoulos, Konstantinos Dimitriadis, Stavros Yannikakis, Aristidis Galiatsatos, Pepie Tsolka
Zitieren
APA
Nikolopoulos, M., Dimitriadis, K., Yannikakis, S., Galiatsatos, A., & Tsolka, P. (2025). Influence of repeated porcelain firing cycles on the microstructure, marginal and internal fit of implant‐cemented Co‐Cr frameworks. European Journal of Oral Sciences. https://doi.org/10.1111/eos.70009
Vancouver
Nikolopoulos M, Dimitriadis K, Yannikakis S, Galiatsatos A, Tsolka P. Influence of repeated porcelain firing cycles on the microstructure, marginal and internal fit of implant‐cemented Co‐Cr frameworks. European Journal of Oral Sciences. 2025. doi:10.1111/eos.70009
BibTeX
@article{Nikolopoulos2025,
author = {Nikolopoulos, Michael and Dimitriadis, Konstantinos and Yannikakis, Stavros and Galiatsatos, Aristidis and Tsolka, Pepie},
title = {Influence of repeated porcelain firing cycles on the microstructure, marginal and internal fit of implant‐cemented Co‐Cr frameworks},
journal = {European Journal of Oral Sciences},
year = {2025},
doi = {10.1111/eos.70009}
}
EUVIMED