Microstructural and mechanical characterization of six Co-Cr alloys made by conventional casting and selective laser melting
The Journal of Prosthetic Dentistry · 2024-09 · 132 (3) · 646.e1-646.e10
DOI: 10.1016/j.prosdent.2024.06.015 ↗Kurz gefasst
Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2024-09. Verfasst von Youssef S Al Jabbari und 3 weiteren Autor:innen. Beteiligte Einrichtung: Director, Dental Biomaterials Research and Development Chair and Professor, Prosthetic Dental Sciences Department, College of Dentistry, King Saud Un…. Hauptthemen laut MEDLINE: Chromium Alloys, Dental Casting Technique, Lasers, Materials Testing. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 48 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: Ministry of Education - Kingdom of Saudi Arabia, King Saud University Deanship of Scientific Research.
Abstract (Originalsprache)
STATEMENT OF PROBLEM: Three Co-Cr alloy types (Co-Cr-Mo, Co-Cr-W, and Co-Cr-Mo-W) have been commonly used in the fabrication of dental prostheses. These alloys can be manufactured using either conventional casting or selective laser melting (SLM) techniques. Nevertheless, research that directly compares these materials and/or manufacturing processes in terms of their microstructural and mechanical characteristics is sparse. PURPOSE: The purpose of this in vitro study was to conduct microstructural and mechanical analysis via X-ray interpretation, optical microscopy, scanning electron microscopy/energy dispersive X-ray spectroscopy (SEM/EDS), image analysis, X-ray diffraction (XRD), instrumented indentation testing (IIT), and 3-point bending testing to characterize Co-Cr-Mo, Co-Cr-W, and Co-Cr-Mo-W alloys produced through conventional casting and SLM. MATERIAL AND METHODS: Six Co-Cr-based alloys were analyzed and divided into 3 types based on their elemental composition (Co-Cr-Mo, Co-Cr-W, and Co-Cr-Mo-W). Additionally, each group was categorized based on the manufacturing process used (casting or SLM). X-ray scans were used to assess porosity. The microstructures of the specimens were assessed through SEM/EDS examination and XRD analysis. IIT was used to determine the Martens hardness (HM) and elastic index (ηIT), while the elastic modulus (E) was estimated through the 3-point bending test. The mechanical properties were statistically analyzed using 2-way analysis of variance (ANOVA) and the Tukey multiple comparison post hoc test, with alloy type and manufacturing process as discriminating variables (α=.05). RESULTS: All cast groups exhibited gross porosity, while no pores or other flaws were found in the SLM groups. Based on the XRD results, the crystalline structure of all Co-Cr specimens consisted of the face-centered cubic γ phase (γ-fcc), along with the hexagonal close-packed ε phase (ε-hcp) and Cr23C6 carbide. Different microstructures were identified between the cast and SLM alloys. Significant differences were identified for the mean standard deviation HM (ranging from 2601 ±94 N/mm2 to 3633 ±61 N/mm2) and mean ±standard deviation ηIT (ranging from 16.8 ±0.3% to 20.9 ±0.3%) among alloys prepared by the same manufacturing process, while all SLM alloys had statistically higher HM and ηIT results than their cast counterparts (P .05), but the SLM alloys had significantly higher results (P
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Substanzen
Autor:innen und Institutionen
- Director, Dental Biomaterials Research and Development Chair and Professor, Prosthetic Dental Sciences Department, College of Dentistry, King Saud University, Riyadh, Saudi Arabia. Electronic address: yaljabbari@ksu.edu…
- Research fellow, Department of Biomaterials, School of Dentistry, National and Kapodistrian Universty of Athens, Athens, Greece.
- Researcher, Dental Biomaterials Research and Development Chair, College of Dentistry, King Saud University, Riyadh, Saudi Arabia.
- Professor, Department of Biomaterials, School of Dentistry, National and Kapodistrian Universty of Athens, Athens, Greece and International Professor of Dental Biomaterials Research and Development Chair, King Saud Univ…
Förderung
- Ministry of Education - Kingdom of Saudi Arabia
- King Saud University Deanship of Scientific Research
Zitieren
APA
Al Jabbari, Y. S., Dimitriadis, K., Sufyan, A., & Zinelis, S. (2024). Microstructural and mechanical characterization of six Co-Cr alloys made by conventional casting and selective laser melting. The Journal of Prosthetic Dentistry, 132(3), 646.e1-646.e10. https://doi.org/10.1016/j.prosdent.2024.06.015
Vancouver
Al Jabbari YS, Dimitriadis K, Sufyan A, Zinelis S. Microstructural and mechanical characterization of six Co-Cr alloys made by conventional casting and selective laser melting. The Journal of Prosthetic Dentistry. 2024;132(3):646.e1-646.e10. doi:10.1016/j.prosdent.2024.06.015
BibTeX
@article{AlJabbari2024,
author = {Al Jabbari, Youssef S and Dimitriadis, Konstantinos and Sufyan, Aref and Zinelis, Spiros},
title = {Microstructural and mechanical characterization of six Co-Cr alloys made by conventional casting and selective laser melting},
journal = {The Journal of Prosthetic Dentistry},
year = {2024},
volume = {132},
number = {3},
pages = {646.e1--646.e10},
doi = {10.1016/j.prosdent.2024.06.015}
}
EUVIMED