EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Bond strength and interfacial analysis of six CoCr alloys made by conventional casting and selective laser melting

Youssef S Al Jabbari iD, Konstantinos Dimitriadis iD, Aref Sufyan, Spiros Zinelis iD

Journal of Prosthodontics · 2024

DOI: 10.1111/jopr.13918 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, 2024. Verfasst von Youssef S Al Jabbari und 3 weiteren Autor:innen. Beteiligte Einrichtung: Dental Biomaterials Research and Development Chair and Prosthetic Dental Sciences Department, College of Dentistry, King Saud University, Riyadh, Sau…. Hauptthemen laut MEDLINE: Dental Bonding, Chromium Alloys, Lasers, Metal Ceramic Alloys. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 39 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Scientific Research for Research Chairs, Deanship of Scientific Research for Research Chairs.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

To investigate the effects of the elemental composition and the manufacturing process of cobalt chromium–molybdenum (CoCr–Mo), cobalt chromium–tungsten (CoCr–W), and CoCr–Mo‐W alloys on metal–ceramic bond strength. Materials and Methods Six CoCr‐based alloys were included in this study, a were classified into three different groups depending on their elemental composition ( Ν = 10, for each group). The first group had molybdenum (Mo) as the third alloying element, the second group contained tungsten (W) (without Mo), and the third group included both alloying elements. The groups were further divided by the manufacturing process (casting or selective laser melting, SLM). Interfacial analysis was carried out using backscattered electron imaging (BEI) and energy‐dispersive X‐ray microanalysis (EDX) operating in line scan mode. The metal‐ceramic bond strength was tested by a 3‐point bending test according to the ISO 9693 requirements. The fracture mode of all specimens was examined under a stereomicroscope. The bond strength results were statistically analyzed by 2‐way ANOVA and Tukey's multiple comparison post hoc test ( a = 0.05).

Results

A continuous interface with the porcelain was found without pores, debonding areas, or other defects. Of the major elements found at the interface, Co showed the highest diffusion rate, while titanium (Ti) had the lowest diffusion rate. No statistically significant differences were identified in metal‐ceramic bond strength either among materials or between manufacturing processes. The fracture mode was found to be cohesive for all specimens.

Conclusions

The metal‐ceramic bond strength is independent of the current CoCr alloy type and manufacturing process when comparing conventional casting and SLM. Interfacial analysis revealed no differences between the tested groups.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Dental BondingChromium AlloysLasersMetal Ceramic AlloysDental Casting TechniqueMaterials TestingMolybdenumSurface PropertiesDental Stress Analysis

Stichwörter der Autor:innen

3‐point bendingCoCr alloysISO 9693PFM alloysSEM/EDXmetallo‐ceramic bond strength

Substanzen

Chromium AlloysMetal Ceramic AlloysMolybdenum

Autor:innen und Institutionen

  • Dental Biomaterials Research and Development Chair and Prosthetic Dental Sciences Department, College of Dentistry, King Saud University, Riyadh, Saudi Arabia.
  • Department of Biomaterials, School of Dentistry, National and Kapodistrian University of Athens, Athens, Greece.
  • Dental Biomaterials Research and Development Chair, College of Dentistry, King Saud University, Riyadh, Saudi Arabia.
  • Department of Biomaterials, School of Dentistry, National and Kapodistrian University of Athens, Athens, Greece and Dental Biomaterials Research and Development Chair, King Saud University, Riyadh, Saudi Arabia.

ORCID-Profile: Youssef S Al Jabbari, Konstantinos Dimitriadis, Spiros Zinelis

Förderung

  • Scientific Research for Research Chairs
  • Deanship of Scientific Research for Research Chairs

Zitieren

APA

Al Jabbari, Y. S., Dimitriadis, K., Sufyan, A., & Zinelis, S. (2024). Bond strength and interfacial analysis of six CoCr alloys made by conventional casting and selective laser melting. Journal of Prosthodontics. https://doi.org/10.1111/jopr.13918

Vancouver

Al Jabbari YS, Dimitriadis K, Sufyan A, Zinelis S. Bond strength and interfacial analysis of six CoCr alloys made by conventional casting and selective laser melting. Journal of Prosthodontics. 2024. doi:10.1111/jopr.13918

BibTeX
@article{AlJabbari2024,
  author = {Al Jabbari, Youssef S and Dimitriadis, Konstantinos and Sufyan, Aref and Zinelis, Spiros},
  title = {Bond strength and interfacial analysis of six CoCr alloys made by conventional casting and selective laser melting},
  journal = {Journal of Prosthodontics},
  year = {2024},
  doi = {10.1111/jopr.13918}
}
Kostenlos starten →