EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Fracture load and failure patterns of zirconia and 3D-printed resin endocrowns: an in vitro study

Okba Mahmoud, Muaiyed Mahmoud Buzayan, Selva Malar Munusamy, Aeman Elkezza, Eshamsul Sulaiman, Maysara Adnan Ibrahim

PeerJ · 2026

DOI: 10.7717/peerj.21602 ↗

Kurz gefasst

Fachartikel in der Zeitschrift PeerJ, 2026. Verfasst von Okba Mahmoud und 5 weiteren Autor:innen. Beteiligte Einrichtung: College of Dentistry, Department of Clinical Sciences, Ajman University, Ajman, United Arab Emirates. Hauptthemen laut MEDLINE: Zirconium, Printing, Three-Dimensional, Crowns, Dental Restoration Failure. Die Arbeit nennt 44 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Background

Endodontically treated teeth are more prone to fracture and often require durable restorative solutions. Endocrowns offer a conservative alternative to conventional post-and-core systems. This in vitro study compared the fracture load and failure behavior of milled zirconia and 3D-printed resin endocrowns. Materials and methods Eighteen extracted human molars were endodontically treated and standardized, then prepared for endocrown restorations using a uniform design (two mm occlusal reduction with a four mm intracoronal extension). Specimens were randomly assigned to receive either Computer-Aided Design (CAD)/ Computer-Aided Manufacturing (CAM) milled zirconia (ZR) or 3D-printed resin-based endocrowns fabricated from VarseoSmile Crown Plus (VS) ( n = 9 per group). Preparations were digitally captured with an intraoral scanner, restorations were designed using CAD software and fabricated by the respective workflows, and all units were cemented with dual cure self-adhesive resin cement. After controlled storage, specimens underwent compressive loading to failure; maximum fracture loads were recorded, and failure modes were categorized according to whether damage was confined to the restoration or involved the tooth structure. Data were assessed for normality and analyzed using an independent samples t -test with Welch correction at a significance level of p < 0.05.

Results

Statistical analysis revealed a highly significant difference in fracture load between the two groups ( p < 0.001), with ZR demonstrating higher strength (3,615.36 ± 792.74 N) compared with VS (1,395.09 ± 149.24 N). However, tooth structure involvement occurred in 8/9 ZR specimens (88.9%), of these, five specimens (55.6% of the total group) were classified as complex/destructive failure, whereas VS failures were simple and confined to the restoration in 5/9 specimens (55.6%), indicating a less severe and potentially repairable failure pattern.

Conclusion

The ZR group showed substantially higher fracture load, but failures more frequently involved tooth structure. VS group exhibited lower strength, yet a higher proportion of simple, potentially repairable fractures confined to the restoration, highlighting a tradeoff between maximum load capacity and repairability. Within the limitations of this in vitro study, these findings support the use of 3D-printed resin endocrowns in selected clinical situations where a tooth preserving endocrown design and digital workflow efficiency are prioritized, and where less severe failure behavior is desirable.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

ZirconiumPrinting, Three-DimensionalCrownsDental Restoration FailureHumansComputer-Aided DesignMaterials TestingIn Vitro TechniquesDental Stress AnalysisMolar

Stichwörter der Autor:innen

3D-printingEndocrownFracture resistanceVarseoSmile Crown PlusZirconia

Substanzen

Zirconiumzirconium oxide

Autor:innen und Institutionen

  • College of Dentistry, Department of Clinical Sciences, Ajman University, Ajman, United Arab Emirates.
  • Department of Restorative Dentistry, Faculty of Dentistry, Universiti Malaya, Kuala Lumpur, Malaysia.
  • Department of Restorative Dentistry, College of Dental Medicine University of Sharjah, Sharjah, United Arab Emirates.

Zitieren

APA

Mahmoud, O., Buzayan, M. M., Munusamy, S. M., Elkezza, A., Sulaiman, E., & Ibrahim, M. A. (2026). Fracture load and failure patterns of zirconia and 3D-printed resin endocrowns: an in vitro study. PeerJ. https://doi.org/10.7717/peerj.21602

Vancouver

Mahmoud O, Buzayan MM, Munusamy SM, Elkezza A, Sulaiman E, Ibrahim MA. Fracture load and failure patterns of zirconia and 3D-printed resin endocrowns: an in vitro study. PeerJ. 2026. doi:10.7717/peerj.21602

BibTeX
@article{Mahmoud2026,
  author = {Mahmoud, Okba and Buzayan, Muaiyed Mahmoud and Munusamy, Selva Malar and Elkezza, Aeman and Sulaiman, Eshamsul and Ibrahim, Maysara Adnan},
  title = {Fracture load and failure patterns of zirconia and 3D-printed resin endocrowns: an in vitro study},
  journal = {PeerJ},
  year = {2026},
  doi = {10.7717/peerj.21602}
}
Kostenlos starten →