EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

3D Printing of Block Copolymer-Based Fracture Tough Denture Base Materials

Kai Rist iD, Iris Lamparth, Sadini Omeragic, Lauren Geurds, Benjamin Grob iD, Yohann Catel

Polymers · 04.07.2026 · 18 (13) · 1660

DOI: 10.3390/polym18131660 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 04.07.2026. Verfasst von Kai Rist und 5 weiteren Autor:innen. Beteiligte Einrichtung: Ivoclar Vivadent AG, Bendererstrasse 2, FL-9494 Schaan, Liechtenstein. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The development of 3D printing high-impact denture bases is challenging, as materials exhibiting both high flexural strength/modulus and fracture toughness are required. Nowadays, most of the commercially available 3D printing denture bases contain significant amounts of crosslinking monomers and therefore behave as brittle materials. In this contribution, urethane dimethacrylate DMA1/(octahydro-4,7-methano-1H-indenyl)methyl acrylate (OMIMA) 1/1 (wt/wt) formulations containing a poly(ε-caprolactone)-polydimethylsiloxane-poly(ε-caprolactone) (PCL-PDMS-PCL) triblock copolymer (BCP1) and fumed silica SiO2-NPs were evaluated for DLP 3D printing of fracture-tough denture bases. The post-curing step was performed at various temperatures (RT, 60 °C, 80 °C, 100 °C and 120 °C). This parameter was shown to strongly influence the Tg and mechanical properties of 3D printed materials. A post-curing temperature of 100 °C was found to be ideal. Under these conditions, 3D printed materials exhibiting excellent mechanical properties were successfully obtained. Furthermore, the amounts of BCP1 and SiO2-NPs were varied. The formulation containing 8.0 wt% of BCP1 and 10.0 wt% of SiO2-NPs (FS = 67.5 ± 1.3 MPa, FM = 2450 ± 71 MPa, Kmax = 2.11 ± 0.06 MPa m1/2, Wf = 1109 ± 19 J m−2) was able to fulfill the ISO 20795-1:2013 requirements in terms of flexural strength (FS)/modulus (FM) and fracture toughness for denture bases with improved impact resistance (FS > 65 MPa, FM > 2000 MPa, Kmax > 1.9 MPa m1/2, Wf > 900 J m−2). This material showed better performance than the commercially available formulations Printodent® GR-14.2 denture HI (FS = 69.2 ± 1.8 MPa, FM = 2153 ± 76 MPa, Kmax = 0.82 ± 0.04 MPa m1/2, Wf = 79 ± 10 J m−2) and Lucitone Digital PrintTM 3D denture base (FS = 56.7 ± 1.9 MPa, FM = 2144 ± 12 MPa, Kmax = 1.92 ± 0.09 MPa m1/2, Wf = 1272 ± 177 J m−2).

Schlagwörter

Stichwörter der Autor:innen

3D printingblock copolymersdenture basefracture toughnesshigh impact

Autor:innen und Institutionen

  • Ivoclar Vivadent AG, Bendererstrasse 2, FL-9494 Schaan, Liechtenstein.

ORCID-Profile: Kai Rist, Benjamin Grob

Zitieren

APA

Rist, K., Lamparth, I., Omeragic, S., Geurds, L., Grob, B., & Catel, Y. (2026). 3D Printing of Block Copolymer-Based Fracture Tough Denture Base Materials. Polymers, 18(13), 1660. https://doi.org/10.3390/polym18131660

Vancouver

Rist K, Lamparth I, Omeragic S, Geurds L, Grob B, Catel Y. 3D Printing of Block Copolymer-Based Fracture Tough Denture Base Materials. Polymers. 2026;18(13):1660. doi:10.3390/polym18131660

BibTeX
@article{Rist2026,
  author = {Rist, Kai and Lamparth, Iris and Omeragic, Sadini and Geurds, Lauren and Grob, Benjamin and Catel, Yohann},
  title = {3D Printing of Block Copolymer-Based Fracture Tough Denture Base Materials},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {13},
  pages = {1660},
  doi = {10.3390/polym18131660}
}
Kostenlos starten →