EUVIMEDEUVIMED entdecken
Crossref

Flexural strength, fracture toughness, translucency, stain resistance, and water sorption of 3D‐printed, milled, and conventional denture base materials

Nathaniel C Lawson iD, Yamen Safadi, Aaron Alford, Himanshi Aggarwal, Pranit V Bora, Thomas J Lawson, Daniel A Givan

Journal of Prosthodontics · 2026-04 · 35 (4) · 553-560

DOI: 10.1111/jopr.13955 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, online erschienen am 24.09.2024. Verfasst von Nathaniel C Lawson und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Clinical and Community Sciences, School of Dentistry, The University of Alabama at Birmingham, Birmingham, Alabama, USA. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Denture Bases, Flexural Strength, Dental Materials. Die Arbeit wurde bisher 18-mal zitiert (Crossref) und nennt 28 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

To compare mechanical, optical, and physical properties of denture base materials fabricated with various 3D printing systems to reference milled and conventionally heat‐processed denture base materials. Materials and Methods Specimens of denture base materials were either 3D‐printed (DLP in‐office printer, CLIP laboratory printer, or material jetting laboratory printer), milled, or heat processed. 3‐point bend flexural strength testing was performed after 50 hours of water storage following 1hour of drying (dry testing) or in 37°C water (wet testing). Fracture toughness was performed with a notched beam specimen after 7 days of water storage and tested dry. The translucency parameter was measured with 2 mm thick specimens. Stain resistance was measured as color change following 14 days of storage in 37°C coffee. Water sorption was measured following 7 days of storage in 37°C distilled water.

Results

For dry testing, all but one of the 3D‐printed materials attained higher or equivalent flexural strength as the reference materials. For wet testing, all 3D‐printed materials attained higher or equivalent strength as the reference materials and dry‐tested materials. For 3D‐printed materials, wet testing increased displacement before fracture whereas it decreased displacement for the reference materials. Only two of the 3D‐printed materials had similar fracture toughness as the reference materials. One of the 3D‐printed materials was more translucent and one was more opaque than the reference materials. Only one of the 3D‐printed materials absorbed more water than the reference materials.

Conclusion

3D‐printed denture base materials have mostly equivalent mechanical, optical, and physical properties to conventional and milled denture base materials.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalDenture BasesFlexural StrengthDental MaterialsMaterials TestingWaterHumansDental Stress Analysis

Stichwörter der Autor:innen

denturemechanical propertiesremovable prosthodontics

Substanzen

WaterDental Materials

Autor:innen und Institutionen

  • Department of Clinical and Community Sciences, School of Dentistry, The University of Alabama at Birmingham, Birmingham, Alabama, USA.
  • Department of Restorative Sciences, School of Dentistry, The University of Alabama at Birmingham, Birmingham, Alabama, USA.
  • Department of Chemistry, UAB College of Arts and Sciences, Birmingham, Alabama, USA.
  • Division of Clinic Essentials and Simulation, School of Dentistry, University of Detroit Mercy, Detroit, USA.

ORCID-Profile: Nathaniel C Lawson

Zitieren

APA

Lawson, N. C., Safadi, Y., Alford, A., Aggarwal, H., Bora, P. V., Lawson, T. J., & Givan, D. A. (2026). Flexural strength, fracture toughness, translucency, stain resistance, and water sorption of 3D‐printed, milled, and conventional denture base materials. Journal of Prosthodontics, 35(4), 553-560. https://doi.org/10.1111/jopr.13955

Vancouver

Lawson NC, Safadi Y, Alford A, Aggarwal H, Bora PV, Lawson TJ, et al. Flexural strength, fracture toughness, translucency, stain resistance, and water sorption of 3D‐printed, milled, and conventional denture base materials. Journal of Prosthodontics. 2026;35(4):553-560. doi:10.1111/jopr.13955

BibTeX
@article{Lawson2026,
  author = {Lawson, Nathaniel C and Safadi, Yamen and Alford, Aaron and Aggarwal, Himanshi and Bora, Pranit V and Lawson, Thomas J and Givan, Daniel A},
  title = {Flexural strength, fracture toughness, translucency, stain resistance, and water sorption of 3D‐printed, milled, and conventional denture base materials},
  journal = {Journal of Prosthodontics},
  year = {2026},
  volume = {35},
  number = {4},
  pages = {553--560},
  doi = {10.1111/jopr.13955}
}
Kostenlos starten →