EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Fracture Toughness, Work of Fracture and Hardness of 3D-Printed Denture Base Resins

Sebastian Hetzler iD, Sebastian Rehm, Sven Räther, Stefan Rues iD, Andreas Zenthöfer, Peter Rammelsberg, Franz Sebastian Schwindling

Materials · 16.09.2025 · 18 (18) · 4338

DOI: 10.3390/ma18184338 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 16.09.2025. Verfasst von Sebastian Hetzler und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Medical Faculty, Heidelberg University, Im Neuenheimer Feld 400, 69120 Heidelberg, Germany. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 40 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Scientific fund of the Österreichische Gesellschaft für Zahn-, Mund- und Kieferheilkunde.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objectives

To compare fracture toughness (FT), work of fracture (WOF) and Vickers hardness (HV) of four 3D-printed denture base resins—including two novel formulations—and one conventional cold-cured polymethylmethacrylate (PMMA) resin.

Methods

3D-printed specimens (Freeprint denture (FD)/denture impact (FDI), DETAX GmbH and V-Print dentbase/dentbase 2.0, VOCO GmbH) were fabricated at 90° layer orientation (n = 40/group) and notched according to ISO 20795-1. FT and WOF were measured via single-edge notched bend testing after seven-day water storage at 37 °C. HV was determined on fractured shards using 3 N load. Data were analyzed with Welch-ANOVA/Dunnett-T3 or ANOVA/Tukey (α = 0.05).

Results

The conventional PMMA showed the highest FT and WOF, followed by the novel formulations of the 3D-printed groups VD2 and FDI. Lowest FT and WOF values were measured for VD and FD. HV was highest for the conventional PMMA, followed by the primary formulations FD and VD. Lowest hardness was measured for the novel formulations FDI and VD2.

Conclusions

The formulations of the novel 3D-printed materials (FDI and VD2) exhibited markedly greater FT and WOF than their respective predecessors, although this improvement was accompanied by a decrease in hardness. Nevertheless, none of the 3D-printed materials fulfilled the ISO standard criteria for enhanced FT.

Schlagwörter

Stichwörter der Autor:innen

3D-printingVickers hardnessdenture basefracture toughness

Autor:innen und Institutionen

  • Department of Prosthodontics, Medical Faculty, Heidelberg University, Im Neuenheimer Feld 400, 69120 Heidelberg, Germany.
  • Department of Prosthetic Dentistry, Medical University of Innsbruck, 6020 Innsbruck, Austria.

ORCID-Profile: Sebastian Hetzler, Stefan Rues

Förderung

  • Scientific fund of the Österreichische Gesellschaft für Zahn-, Mund- und Kieferheilkunde

Zitieren

APA

Hetzler, S., Rehm, S., Räther, S., Rues, S., Zenthöfer, A., Rammelsberg, P., & Schwindling, F. S. (2025). Fracture Toughness, Work of Fracture and Hardness of 3D-Printed Denture Base Resins. Materials, 18(18), 4338. https://doi.org/10.3390/ma18184338

Vancouver

Hetzler S, Rehm S, Räther S, Rues S, Zenthöfer A, Rammelsberg P, et al. Fracture Toughness, Work of Fracture and Hardness of 3D-Printed Denture Base Resins. Materials. 2025;18(18):4338. doi:10.3390/ma18184338

BibTeX
@article{Hetzler2025,
  author = {Hetzler, Sebastian and Rehm, Sebastian and Räther, Sven and Rues, Stefan and Zenthöfer, Andreas and Rammelsberg, Peter and Schwindling, Franz Sebastian},
  title = {Fracture Toughness, Work of Fracture and Hardness of 3D-Printed Denture Base Resins},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {18},
  pages = {4338},
  doi = {10.3390/ma18184338}
}
Kostenlos starten →