Impact of Printing Angle and Layer Height on the Mechanical Strength of PLA Reinforced with Chopped Carbon Fibres Using FDM 3D Printing
Polymers · 19.11.2025 · 17 (22) · 3069
DOI: 10.3390/polym17223069 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 19.11.2025. Verfasst von Oscar Araque und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, Universidad de Ibagué, Ibagué 730001, Colombia. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 39 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministerio de Ciencia, Tecnología e Innovación, Ministerio de Ciencia, Tecnología e Innovación, Min-ciencias.
Abstract (Originalsprache)
This research addresses the inherent limitations of low mechanical strength in FDM-printed materials by studying Carbon Fibre-reinforced Polylactic Acid (PLA-CF) composites. The low strength limitation of PLA-CF in FDM requires identifying the most suitable print angle and layer height parameters. This study maximises its structural robustness, filling a knowledge gap regarding its combined effect on tensile and flexural strength. The main objective was to find the best printing angle and layer height to improve mechanical performance, an important requirement for advancing additive manufacturing applications. A total of 210 FDM-printed specimens of the PLA-CF material were subjected to uniaxial tensile (ASTM D3039) and three-point bending (ASTM D790) tests, systematically varying the printing angles (0–90°) and layer heights of 0.1, 0.2, and 0.3 mm, following a full experimental design matrix. The ANOVA method has been used to determine the significant effect of factors on the established parameters. The findings indicated that both factors had a pronounced effect on the mechanical strength. Printing at lower angles (0° and 15°) provided, on average, greater resistance under tension (up to ~3920 N for a layer height of 0.1 mm), as well as under bending (up to 88.54 N for the same layer height), attributed to favourable fibre alignment and better load distribution. Conversely, higher angles (60° to 90°) drastically reduced strength (tensile failures due to delamination; bending forces as low as 30.02 N for a layer height of 0.3 mm, highlighting the weakness of perpendicular layer interfaces. Furthermore, lower layer height could result in better overall mechanical properties. In conclusion, FDM parameters with low print angles and reduced layer heights are essential for maximising the mechanical robustness and structural integrity of PLA-CF parts, enabling the identification of improved production processes for industrial applications and educational prototypes, among others.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Mechanical Engineering, Universidad de Ibagué, Ibagué 730001, Colombia.
- Departamento de Fisica, Facultad Ciencias, Universidad del Tolima, Barrio Santa Helena A.A. 546, Ibagué 730006299, Colombia.
- Departamento de Producción y Sanidad Vegetal, Facultad Ingeniería Agronómica, Universidad del Tolima, Barrio Santa Helena A.A. 546, Ibagué 730006299, Colombia.
ORCID-Profile: Oscar Araque, Luz Adriana Sánchez-Echeverri, Ivonne X Cerón
Förderung
- Ministerio de Ciencia, Tecnología e Innovación
- Ministerio de Ciencia, Tecnología e Innovación, Min-ciencias
Zitieren
APA
Araque, O., Sánchez-Echeverri, L. A., & Cerón, I. X. (2025). Impact of Printing Angle and Layer Height on the Mechanical Strength of PLA Reinforced with Chopped Carbon Fibres Using FDM 3D Printing. Polymers, 17(22), 3069. https://doi.org/10.3390/polym17223069
Vancouver
Araque O, Sánchez-Echeverri LA, Cerón IX. Impact of Printing Angle and Layer Height on the Mechanical Strength of PLA Reinforced with Chopped Carbon Fibres Using FDM 3D Printing. Polymers. 2025;17(22):3069. doi:10.3390/polym17223069
BibTeX
@article{Araque2025,
author = {Araque, Oscar and Sánchez-Echeverri, Luz Adriana and Cerón, Ivonne X},
title = {Impact of Printing Angle and Layer Height on the Mechanical Strength of PLA Reinforced with Chopped Carbon Fibres Using FDM 3D Printing},
journal = {Polymers},
year = {2025},
volume = {17},
number = {22},
pages = {3069},
doi = {10.3390/polym17223069}
}
EUVIMED