EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

FDM 3D Printing and Properties of PBS/PLA Blends

Wangwang Yu iD, Liwei Sun, Mengya Li, Meihui Li, Wen Lei, Chaohui Wei

Polymers · 02.11.2023 · 15 (21) · 4305

DOI: 10.3390/polym15214305 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 02.11.2023. Verfasst von Wangwang Yu und 5 weiteren Autor:innen. Beteiligte Einrichtung: School of Mechanical Engineering, Nanjing Vocational University of Industry Technology, Nanjing 210023, China. Die Arbeit wurde bisher 49-mal zitiert (Crossref) und nennt 50 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: The Natural Science Foundation of the Jiangsu Higher Education Institutions of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Poly(lactic acid) (PLA) and Poly(butylene succinate) (PBS) were chosen as raw materials and melt blended by a twin screw extruder and pelletized; then, the pellets were extruded into filaments; after that, various PBS/PLA blending samples were prepared by Fused Deposition Molding (FDM) 3D printing technology using the filaments obtained and the effect of the dosage of PBS on technological properties of 3D-printed specimens was investigated. For comparison, the PLA specimen was also prepared by FDM printing. The tensile strength, tensile modulus, thermal stability, and hydrophilicity became poorer with increasing the dosage of PBS, while the flexural strength, flexural modulus, impact strength, and crystallinity increased first and then decreased. The blend containing 10% PBS (10% PBS/PLA) had the greatest flexural strength of 60.12 MPa, tensile modulus of 2360.04 MPa, impact strength of 89.39 kJ/m2, and crystallinity of 7.4%, which were increased by 54.65%, 61.04%, 14.78%, and 51.02% compared to those of printed PLA, respectively; this blend also absorbed the least water than any other specimen when immersed in water. Different from the transparent PLA filament, 10% PBS/PLA filament presented a milky white appearance. The printed 10% PBS/PLA specimen had a smooth surface, while the surface of the printed PLA was rough. All the results indicated that the printed 10% PBS/PLA specimen had good comprehensive properties, including improved mechanical properties, crystallization performance, and surface quality than PLA, as well as proper wettability and water absorption. The prominent conclusion achieved in this work was that 10% PBS/PLA should be an ideal candidate for biodegradable feedstock among all the PBS/PLA blends for FDM 3D printing.

Schlagwörter

Stichwörter der Autor:innen

3D printingblendfused deposition moldingpoly(butylene succinate)poly(lactic acid)property

Autor:innen und Institutionen

  • School of Mechanical Engineering, Nanjing Vocational University of Industry Technology, Nanjing 210023, China.
  • College of Science, Nanjing Forestry University, Nanjing 210037, China.

ORCID-Profile: Wangwang Yu

Förderung

  • The Natural Science Foundation of the Jiangsu Higher Education Institutions of China

Zitieren

APA

Yu, W., Sun, L., Li, M., Li, M., Lei, W., & Wei, C. (2023). FDM 3D Printing and Properties of PBS/PLA Blends. Polymers, 15(21), 4305. https://doi.org/10.3390/polym15214305

Vancouver

Yu W, Sun L, Li M, Li M, Lei W, Wei C. FDM 3D Printing and Properties of PBS/PLA Blends. Polymers. 2023;15(21):4305. doi:10.3390/polym15214305

BibTeX
@article{Yu2023,
  author = {Yu, Wangwang and Sun, Liwei and Li, Mengya and Li, Meihui and Lei, Wen and Wei, Chaohui},
  title = {FDM 3D Printing and Properties of PBS/PLA Blends},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {21},
  pages = {4305},
  doi = {10.3390/polym15214305}
}
Infokarte | EUVIMED

Artikeldaten derzeit nicht verfügbar.

Recherche