EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of Cooling Rate on the Flexural and Impact Properties of Compression Molded Non-Woven Flax/PLA Biocomposites

Anurag Pisupati, Marco Curto, Thomas Laurent, Benoit Cosson, Chung Hae Park iD, Hom Nath Dhakal iD

Polymers · 13.02.2025 · 17 (4) · 493

DOI: 10.3390/polym17040493 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 13.02.2025. Verfasst von Anurag Pisupati und 5 weiteren Autor:innen. Beteiligte Einrichtung: Center for Materials and Processes, IMT Nord Europe, Institut Mines-Télécom, Université de Lille, 59000 Lille, France. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 64 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: European Regional Development Fund (ERDF), INTERREG 2SEAS.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This work investigates the influence of crystallinity on the mechanical properties of needle-punched non-woven flax/polylactic acid (PLA) biocomposites with different flax fiber contents. Biocomposites were fabricated by a compression molding adopting different cooling rates to understand the mechanism of crystallinity and their contribution to the mechanical properties. Image-based analysis of the fiber distribution in non-woven preform indicates the probable origins of the residual porosities and the potential nucleation sites for crystal formation within the composites. The improvement of 25% and 100% in flexural modulus is observed for the composites with 40% and 50% of flax fiber mass fractions, respectively, when subjected to a lower cooling rate, which implies the significant influence of the void content on the brittleness of composites. The impact properties of the composites decrease from 11% to 18% according to the flax fiber mass fraction when the cooling rate decreases to 1 °C/min, and the composites become more brittle. The induced impact and flexural properties of the composites are compared with those of other composites in the literature to emphasize their applicability to semi-structural applications.

Schlagwörter

Stichwörter der Autor:innen

crystallinityflax fiberflexural propertiespolylactic acid (PLA)process cycle timethermal degradation

Autor:innen und Institutionen

  • Center for Materials and Processes, IMT Nord Europe, Institut Mines-Télécom, Université de Lille, 59000 Lille, France.
  • Wärtsilä Defence Solutions UK Limited, 4 Marples Way, Havant PO9 1NX, UK.
  • Centre Européen des Textiles Innovants, 59355 Tourcoing, France.
  • Advanced Polymers and Composites (APC) Research Group, School of Mechanical and Design Engineering, University of Portsmouth, Portsmouth PO1 3DJ, UK.

ORCID-Profile: Chung Hae Park, Hom Nath Dhakal

Förderung

  • European Regional Development Fund (ERDF), INTERREG 2SEAS

Zitieren

APA

Pisupati, A., Curto, M., Laurent, T., Cosson, B., Park, C. H., & Dhakal, H. N. (2025). Influence of Cooling Rate on the Flexural and Impact Properties of Compression Molded Non-Woven Flax/PLA Biocomposites. Polymers, 17(4), 493. https://doi.org/10.3390/polym17040493

Vancouver

Pisupati A, Curto M, Laurent T, Cosson B, Park CH, Dhakal HN. Influence of Cooling Rate on the Flexural and Impact Properties of Compression Molded Non-Woven Flax/PLA Biocomposites. Polymers. 2025;17(4):493. doi:10.3390/polym17040493

BibTeX
@article{Pisupati2025,
  author = {Pisupati, Anurag and Curto, Marco and Laurent, Thomas and Cosson, Benoit and Park, Chung Hae and Dhakal, Hom Nath},
  title = {Influence of Cooling Rate on the Flexural and Impact Properties of Compression Molded Non-Woven Flax/PLA Biocomposites},
  journal = {Polymers},
  year = {2025},
  volume = {17},
  number = {4},
  pages = {493},
  doi = {10.3390/polym17040493}
}
Kostenlos starten →