EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC 4.0

Process‐Induced Anisotropy and Fracture Behavior of Pellet‐ 3D Printed PLA and PLA /Flax Biocomposites

Fernando Ancio, Luis Távara, Luis Miguel Ferreira

Polymer Composites · 20.09.2026 · 47 (18) · 16442-16462

DOI: 10.1002/pc.71361 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymer Composites, online erschienen am 27.06.2026. Verfasst von Fernando Ancio und 2 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 42 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0). Gefördert von: Ministerio de Ciencia, Innovación y Universidades.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Fused granular fabrication (FGF) enables cost‐effective, large‐scale polymer additive manufacturing; however, the mechanical behavior and fracture response of pellet extruded parts, particularly for natural‐fiber composites, remain insufficiently characterized. This study evaluates the tensile response and fracture mechanisms of neat polylactic acid (PLA) and flax fiber‐reinforced PLA (PLA/Flax) produced by FGF. Two hundred specimens are tested to quantify the influence of raster orientation and layer height on process‐induced anisotropy. Tensile strength, elastic modulus, and density are measured, utilizing density‐normalized metrics to reduce scatter, while fracture surfaces are analyzed by 3D optical profilometry. FGF‐processed PLA reaches tensile strengths up to 59.5 MPa for a 0° raster orientation, whereas PLA/Flax achieves up to 45.82 MPa. Both materials present reduced elastic stiffness, with moduli approximately 40%–50% lower than common reference values. Reducing the layer height generally improves the mechanical performance and reduces the orientation sensitivity but increases the printing time and production cost. Profilometry confirms that anisotropy is governed by bead orientation and bonding quality. A reduction of approximately 46% in the average fracture surface roughness of representative PLA/Flax composite specimens was observed as layer height decreased, correlating with an increase in density‐normalized tensile strength. These results provide practical guidance for selecting raster strategies to balance mechanical performance with manufacturing efficiency in pellet‐based printing.

Förderung

  • Ministerio de Ciencia, Innovación y Universidades

Zitieren

APA

Ancio, F., Távara, L., & Ferreira, L. M. (2026). Process‐Induced Anisotropy and Fracture Behavior of Pellet‐ 3D Printed PLA and PLA /Flax Biocomposites. Polymer Composites, 47(18), 16442-16462. https://doi.org/10.1002/pc.71361

Vancouver

Ancio F, Távara L, Ferreira LM. Process‐Induced Anisotropy and Fracture Behavior of Pellet‐ 3D Printed PLA and PLA /Flax Biocomposites. Polymer Composites. 2026;47(18):16442-16462. doi:10.1002/pc.71361

BibTeX
@article{Ancio2026,
  author = {Ancio, Fernando and Távara, Luis and Ferreira, Luis Miguel},
  title = {Process‐Induced Anisotropy and Fracture Behavior of Pellet‐ 3D Printed PLA and PLA /Flax Biocomposites},
  journal = {Polymer Composites},
  year = {2026},
  volume = {47},
  number = {18},
  pages = {16442--16462},
  doi = {10.1002/pc.71361}
}
Kostenlos starten →