EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effects of Nozzle Temperature on Mechanical Properties of Polylactic Acid Specimens Fabricated by Fused Deposition Modeling

Fernando Rivera-López iD, María M Laz Pavón iD, Eduardo Cabello Correa, María Hernández Molina iD

Polymers · 29.06.2024 · 16 (13) · 1867

DOI: 10.3390/polym16131867 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 29.06.2024. Verfasst von Fernando Rivera-López und 3 weiteren Autor:innen. Beteiligte Einrichtung: Departamento de Ingeniería Industrial, Escuela Superior de Ingeniería y Tecnología, Universidad de La Laguna, Apdo. 456, E-38200 San Cristóbal de La …. Die Arbeit wurde bisher 78-mal zitiert (Crossref) und nennt 48 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Universidad de La Laguna, the Plan Propio de Investigación 2022 of the Universidad de La Laguna through Proyectos Dirigidos por Noveles Investigadores/as.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This paper investigates the effect of nozzle temperature, from 180 to 260 °C, on properties of polylactic acid (PLA) samples manufactured by fused deposition modeling (FDM) technology. The main objective of this research is to determinate an optimum nozzle temperature relative to tensile, flexural and compressive properties of printed specimens. After manufacturing, the samples exhibit an amorphous structure, without crystallization effects, independently of the fabrication temperature. In order to determine the influence of printing temperature on mechanical properties, uniaxial tensile, three-point flexural and compression strength tests were carried out. The obtained results suggest that a relative low printing temperature could reduce the material flow and decrease the density of the final prototype, with a negative effect on both the quality and the mechanical properties of the pieces. If temperature increases up to 260 °C, an excess of material can be deposited, but with no significant negative effect on mechanical parameters. There is an optimum nozzle temperature interval, depending on the considered piece and test, for which mechanical values can be optimized. Taking into account all tests, a recommended extruder temperature interval may be identified as 220–240 °C. This range encompasses all mechanical parameters, avoiding the highest temperature where an excess of material was observed. For this printing temperature interval, no significant mechanical variations were appreciated, which corresponds to a stable behavior of the manufactured specimens.

Schlagwörter

Stichwörter der Autor:innen

3D printingfused deposition modelingmechanical propertiesnozzle temperaturepolylactic acid

Autor:innen und Institutionen

  • Departamento de Ingeniería Industrial, Escuela Superior de Ingeniería y Tecnología, Universidad de La Laguna, Apdo. 456, E-38200 San Cristóbal de La Laguna, Santa Cruz de Tenerife, Spain.

ORCID-Profile: Fernando Rivera-López, María M Laz Pavón, María Hernández Molina

Förderung

  • Universidad de La Laguna
  • the Plan Propio de Investigación 2022 of the Universidad de La Laguna through Proyectos Dirigidos por Noveles Investigadores/as

Zitieren

APA

Rivera-López, F., Pavón, M. M. L., Correa, E. C., & Molina, M. H. (2024). Effects of Nozzle Temperature on Mechanical Properties of Polylactic Acid Specimens Fabricated by Fused Deposition Modeling. Polymers, 16(13), 1867. https://doi.org/10.3390/polym16131867

Vancouver

Rivera-López F, Pavón MML, Correa EC, Molina MH. Effects of Nozzle Temperature on Mechanical Properties of Polylactic Acid Specimens Fabricated by Fused Deposition Modeling. Polymers. 2024;16(13):1867. doi:10.3390/polym16131867

BibTeX
@article{RiveraLpez2024,
  author = {Rivera-López, Fernando and Pavón, María M Laz and Correa, Eduardo Cabello and Molina, María Hernández},
  title = {Effects of Nozzle Temperature on Mechanical Properties of Polylactic Acid Specimens Fabricated by Fused Deposition Modeling},
  journal = {Polymers},
  year = {2024},
  volume = {16},
  number = {13},
  pages = {1867},
  doi = {10.3390/polym16131867}
}
Kostenlos starten →