The Effects of Self-Polymerized Polydopamine Coating on Mechanical Properties of Polylactic Acid (PLA)–Kenaf Fiber (KF) in Fused Deposition Modeling (FDM)
Polymers · 30.05.2023 · 15 (11) · 2525
DOI: 10.3390/polym15112525 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 30.05.2023. Verfasst von Sanusi Hamat und 9 weiteren Autor:innen. Beteiligte Einrichtung: Department of Aerospace Engineering, Faculty of Engineering, Universiti Putra Malaysia, Serdang 43400, Selangor, Malaysia. Die Arbeit wurde bisher 31-mal zitiert (Crossref) und nennt 74 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Higher Education, Ministry of Higher Education, Malaysia.
Abstract (Originalsprache)
This research examines the impact of self-polymerized polydopamine (PDA) coating on the mechanical properties and microstructural behavior of polylactic acid (PLA)/kenaf fiber (KF) composites in fused deposition modeling (FDM). A biodegradable FDM model of natural fiber-reinforced composite (NFRC) filaments, coated with dopamine and reinforced with 5 to 20 wt.% bast kenaf fibers, was developed for 3D printing applications. Tensile, compression, and flexural test specimens were 3D printed, and the influence of kenaf fiber content on their mechanical properties was assessed. A comprehensive characterization of the blended pellets and printed composite materials was performed, encompassing chemical, physical, and microscopic analyses. The results demonstrate that the self-polymerized polydopamine coating acted as a coupling agent, enhancing the interfacial adhesion between kenaf fibers and the PLA matrix and leading to improved mechanical properties. An increase in density and porosity was observed in the FDM specimens of the PLA–PDA–KF composites, proportional to their kenaf fiber content. The enhanced bonding between kenaf fiber particles and the PLA matrix contributed to an increase of up to 13.4% for tensile and 15.3% for flexural in the Young’s modulus of PLA–PDA–KF composites and an increase of up to 30% in compressive stress. The incorporation of polydopamine as a coupling agent in the FDM filament composite led to an improvement in tensile, compressive, and flexural stresses and strain at break, surpassing that of pure PLA, while the reinforcement provided by kenaf fibers was enhanced more by delayed crack growth, resulting in a higher strain at break. The self-polymerized polydopamine coatings exhibit remarkable mechanical properties, suggesting their potential as a sustainable material for diverse applications in FDM.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Aerospace Engineering, Faculty of Engineering, Universiti Putra Malaysia, Serdang 43400, Selangor, Malaysia.
- Faculty of Mechanical Engineering & Technology, Universiti Malaysia Perlis, Ulu Pauh 02600, Perlis, Malaysia.
- Aerospace Malaysia Research Centre (AMRC), Universiti Putra Malaysia, Serdang 43400, Selangor, Malaysia.
- Laboratory of Biocomposite Technology, Institute of Tropical Forestry and Forest Products (INTROP), Universiti Putra Malaysia, Serdang 43400, Selangor, Malaysia.
- Department of Mechanical and Manufacturing Engineering, Universiti Putra Malaysia, Serdang 43400, Selangor, Malaysia.
- Advanced Engineering Materials and Composites Research Centre (AEMC), Department of Mechanical and Manufacturing Engineering, Universiti Putra Malaysia, Serdang 43400, Selangor, Malaysia.
ORCID-Profile: Sanusi Hamat, Mohd Sapuan Salit, Noorfaizal Yidris, Syamir Alihan Showkat Ali
Förderung
- Ministry of Higher Education
- Ministry of Higher Education, Malaysia
Zitieren
APA
Hamat, S., Ishak, M. R., Salit, M. S., Yidris, N., Showkat Ali, S. A., Hussin, M. S., Abdul Manan, M. S., Ahamad Suffin, M. Q. Z., Ibrahim, M., & Mohd Khalil, A. N. (2023). The Effects of Self-Polymerized Polydopamine Coating on Mechanical Properties of Polylactic Acid (PLA)–Kenaf Fiber (KF) in Fused Deposition Modeling (FDM). Polymers, 15(11), 2525. https://doi.org/10.3390/polym15112525
Vancouver
Hamat S, Ishak MR, Salit MS, Yidris N, Showkat Ali SA, Hussin MS, et al. The Effects of Self-Polymerized Polydopamine Coating on Mechanical Properties of Polylactic Acid (PLA)–Kenaf Fiber (KF) in Fused Deposition Modeling (FDM). Polymers. 2023;15(11):2525. doi:10.3390/polym15112525
BibTeX
@article{Hamat2023,
author = {Hamat, Sanusi and Ishak, Mohamad Ridzwan and Salit, Mohd Sapuan and Yidris, Noorfaizal and Showkat Ali, Syamir Alihan and Hussin, Mohd Sabri and Abdul Manan, Muhamad Saifuldin and Ahamad Suffin, Muhamad Qauyum Zawawi and Ibrahim, Maliki and Mohd Khalil, Ahmad Nabil},
title = {The Effects of Self-Polymerized Polydopamine Coating on Mechanical Properties of Polylactic Acid (PLA)–Kenaf Fiber (KF) in Fused Deposition Modeling (FDM)},
journal = {Polymers},
year = {2023},
volume = {15},
number = {11},
pages = {2525},
doi = {10.3390/polym15112525}
}
EUVIMED