EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Fracture Resistance Comparative Analysis of Milled-Derived vs. 3D-Printed CAD/CAM Materials for Single-Unit Restorations

Cristian Abad-Coronel iD, Manuel Bravo iD, Salomé Tello iD, Emilia Cornejo, Yirelly Paredes, Cesar A Paltan iD, Jorge I Fajardo iD

Polymers · 15.09.2023 · 15 (18) · 3773

DOI: 10.3390/polym15183773 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 15.09.2023. Verfasst von Cristian Abad-Coronel und 6 weiteren Autor:innen. Beteiligte Einrichtung: CAD/CAM Materials and Digital Dentistry Research Group, Faculty of Dentistry, Universidad de Cuenca, Cuenca 010105, Ecuador. Die Arbeit wurde bisher 20-mal zitiert (Crossref) und nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The aim of this study was to evaluate and compare the fracture resistance of a single-unit fixed prosthesis, using a CAD/CAM PMMA material and two printed materials (3DPPa and 3DPPb). A typodont with a specific preparation for a full crown was used; a digital impression was made with a state-of-the-art scanner (PrimeScanTM, Dentsply-SironaTM, New York, NY, USA), and a full coverage restoration was designed using a biogeneric design proposal by means of specific software (InLAB 22.1, Dentsply-Sirona, NY, USA). Sixty crowns were prepared, divided into three groups according to the material: 3DPPa (n = 20), 3DPPb (n = 20), both 3D-printed from the .STL file with a resolution of 50 μm, and PMMA (n = 20) milled-derived, which were subjected to a thermocycling process. A universal testing machine (Universal/Tensile Testing Machine, Autograph AGS-X Series) with integrated software (TRAPEZIUM LITE X) equipped with a 20 kN load cell was used to determine the fracture resistance. Significant differences were found by Kruskal–Wallis test and multiple comparisons (p < 0.05) in fracture resistance between materials. The fracture resistance for the PMMA material was higher, and the standard deviation was lower (x = 1427.9; sd = 36.9 N) compared to the 3DPPa (x = 1231; sd = 380.1 N) and 3DPPb (x = 1029.9; sd = 166.46 N) prints. The restorations from the milled-derived group showed higher average fracture resistance than the provisional restorations obtained from the printed groups. However, the results demonstrated that all three materials analyzed in single-unit restorations are capable of withstanding the average masticatory forces.

Schlagwörter

Stichwörter der Autor:innen

3D-printingCAD/CAM materialsPMMAfracture resistanceinterim restorations

Autor:innen und Institutionen

  • CAD/CAM Materials and Digital Dentistry Research Group, Faculty of Dentistry, Universidad de Cuenca, Cuenca 010105, Ecuador.
  • Faculty of Dentistry, University of Cuenca, Cuenca 010105, Ecuador.
  • New Materials and Transformation Processes Research Group GiMaT, Universidad Politécnica Salesiana, Cuenca 010105, Ecuador.

ORCID-Profile: Cristian Abad-Coronel, Manuel Bravo, Salomé Tello, Cesar A Paltan, Jorge I Fajardo

Zitieren

APA

Abad-Coronel, C., Bravo, M., Tello, S., Cornejo, E., Paredes, Y., Paltan, C. A., & Fajardo, J. I. (2023). Fracture Resistance Comparative Analysis of Milled-Derived vs. 3D-Printed CAD/CAM Materials for Single-Unit Restorations. Polymers, 15(18), 3773. https://doi.org/10.3390/polym15183773

Vancouver

Abad-Coronel C, Bravo M, Tello S, Cornejo E, Paredes Y, Paltan CA, et al. Fracture Resistance Comparative Analysis of Milled-Derived vs. 3D-Printed CAD/CAM Materials for Single-Unit Restorations. Polymers. 2023;15(18):3773. doi:10.3390/polym15183773

BibTeX
@article{AbadCoronel2023,
  author = {Abad-Coronel, Cristian and Bravo, Manuel and Tello, Salomé and Cornejo, Emilia and Paredes, Yirelly and Paltan, Cesar A and Fajardo, Jorge I},
  title = {Fracture Resistance Comparative Analysis of Milled-Derived vs. 3D-Printed CAD/CAM Materials for Single-Unit Restorations},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {18},
  pages = {3773},
  doi = {10.3390/polym15183773}
}
Kostenlos starten →