Molybdenum Disulphide Modified Polylactide for 3D Printed (FDM/FFF) Filaments
Polymers · 09.05.2023 · 15 (10) · 2236
DOI: 10.3390/polym15102236 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 09.05.2023. Verfasst von Maciej Kujawa und 7 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Mechanical Engineering, Wroclaw University of Science and Technology, Wybrzeże Stanisława Wyspiańskiego 27, 50-370 Wroclaw, Poland. Die Arbeit wurde bisher 15-mal zitiert (Crossref) und nennt 46 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
MoS2 is an additive used to improve the tribological properties of plastics. In this work, it was decided to verify the use of MoS2 as a modifier of the properties of PLA filaments used in the additive FDM/FFF technique. For this purpose, MoS2 was introduced into the PLA matrix at concentrations of 0.025–1.0% by weight. Through extrusion, a fibre with a diameter of 1.75 mm was obtained. 3D printed samples with three different filling patterns were subjected to comprehensive thermal (TG, DSC and HDT), mechanical (impact, bending and strength tests), tribological and physicochemical characteristics. The mechanical properties were determined for two different types of fillings, and samples with the third type of filling were used for tribological tests. Tensile strength has been significantly increased for all samples with longitudinal filling with improvement up to 49%. In terms of tribological properties, higher values of the addition (0.5%) caused a significant increase of up to 457% of the wear indicator. A significant improvement in processing properties in terms of rheology was obtained (416% compared to pure PLA with the addition of 1.0%), which translated into more efficient processing, increased interlayer adhesion and mechanical strength. As a result, the quality of printed objects has been improved. Microscopic analysis was also carried out, which confirmed the good dispersion of the modifier in the polymer matrix (SEM-EDS). Microscopic techniques (MO, SEM) allowed for the characterization of the effect of the additive on changes in the printing process (improvement of interlayer remelting) and to assess impact fractures. In the tribological area, the introduced modification did not bring spectacular effects.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Faculty of Mechanical Engineering, Wroclaw University of Science and Technology, Wybrzeże Stanisława Wyspiańskiego 27, 50-370 Wroclaw, Poland.
- Faculty of Chemistry, Adam Mickiewicz University in Poznań, Uniwersytetu Poznańskiego 8, 61-614 Poznan, Poland.
- Centre for Advanced Technologies, Adam Mickiewicz University, Uniwersytetu Poznańskiego 10, 61-712 Poznan, Poland.
ORCID-Profile: Maciej Kujawa, Wojciech Pawlak, Daria Pakuła
Zitieren
APA
Kujawa, M., Głowacka, J., Pawlak, W., Sztorch, B., Pakuła, D., Frydrych, M., Sokolska, J., & Przekop, R. E. (2023). Molybdenum Disulphide Modified Polylactide for 3D Printed (FDM/FFF) Filaments. Polymers, 15(10), 2236. https://doi.org/10.3390/polym15102236
Vancouver
Kujawa M, Głowacka J, Pawlak W, Sztorch B, Pakuła D, Frydrych M, et al. Molybdenum Disulphide Modified Polylactide for 3D Printed (FDM/FFF) Filaments. Polymers. 2023;15(10):2236. doi:10.3390/polym15102236
BibTeX
@article{Kujawa2023,
author = {Kujawa, Maciej and Głowacka, Julia and Pawlak, Wojciech and Sztorch, Bogna and Pakuła, Daria and Frydrych, Miłosz and Sokolska, Justyna and Przekop, Robert E},
title = {Molybdenum Disulphide Modified Polylactide for 3D Printed (FDM/FFF) Filaments},
journal = {Polymers},
year = {2023},
volume = {15},
number = {10},
pages = {2236},
doi = {10.3390/polym15102236}
}
EUVIMED