Fabrication and Characterization of 3D-Printed Polylactide Composite Scaffolds with Modified Graphene
ACS Omega · 10.11.2026 · 11 (44) · 68341-68353
DOI: 10.1021/acsomega.6c04916 ↗Kurz gefasst
Fachartikel in der Zeitschrift ACS Omega, online erschienen am 27.10.2026. Verfasst von Worathep Khimlek und 8 weiteren Autor:innen. Beteiligte Einrichtung: School of Integrated Science and Innovation, Sirindhorn International Institute of Technology (SIIT), Thammasat University, Pathum Thani 12120, Thail…. Die Arbeit nennt 85 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: Thailand Science Research and Innovation, Sirindhorn International Institute of Technology, Thammasat University, Center of Excellence in Functional Advanced Materials Engineering, Thammasat University.
Abstract (Originalsprache)
In this study, we introduce novel multifunctional biomaterial inks for extrusion-based 3D bioprinting to create scaffolds for potential tissue engineering. This study focuses on developing composite materials by incorporating alkyl ketene dimer (AKD)-modified graphene nanoplatelets (GP) into polylactide (PLA) using a solvent casting technique. GP was synthesized via electrolytic exfoliation in an aqueous poly(sodium 4-styrenesulfonate) solution and subsequently modified with AKD by ball milling to enhance dispersion and PLA compatibility. Physical and chemical characterization confirmed the successful synthesis and structural properties of the AKD-modified GP. PLA-GPD20 films containing 20 wt % AKD-modified GP exhibited significantly improved elongation at break and maintained tensile strength comparable to neat PLA. All biomaterial composite films exhibited high stiffness, as evidenced by glass transition temperatures above room temperature, and electrical conductivity in the semiconductor range. The results highlight the significant positive impact of AKD on the physical and electrical properties, as well as the printability, of the composites. The printability performance potential was evaluated using 10 wt % PLA-GPD20 biomaterial inks to generate scaffolds with different patterns. The mechanical testing of the printed scaffolds revealed that the tensile strength and modulus increased with the incorporation of GPD20. The printing orientation is an effective parameter for tuning the balance between stiffness and ductility; scaffolds printed at 90° exhibited higher Young’s modulus but lower elongation at yield and tensile strength than those printed at 45°. Furthermore, incorporating AKD into GP/PLA composites improved hydrophobicity. The results suggest that AKD-modified graphene composites hold substantial promise for the development of advanced multifunctional materials for tissue engineering applications.
Autor:innen und Institutionen
- School of Integrated Science and Innovation, Sirindhorn International Institute of Technology (SIIT), Thammasat University, Pathum Thani 12120, Thailand.
- Université Claude Bernard Lyon 1, CNRS, ISA-UMR 5280, Villeurbanne 69622, France.
- Department of Materials Science, Faculty of Science, Chulalongkorn University, Bangkok 10330, Thailand.
- National Nanotechnology Center, National Science and Technology Development Agency, Thailand Science Park, Pathum Thani 12120, Thailand.
- Department of Chemical Science and Engineering, Institute of Science Tokyo, 2-12-1, O̅okayama, Meguro-Ku, Tokyo 152-8552, Japan.
- Thai Microelectronics Center, National Science and Technology Development Agency, Thailand Science Park, Pathum Thani 12120, Thailand.
ORCID-Profile: Vitsarut Primpray, Teruoki Tago, Paiboon Sreearunothai, Chariya Kaewsaneha, Pakorn Opaprakasit
Förderung
- Thailand Science Research and Innovation
- Sirindhorn International Institute of Technology, Thammasat University
- Center of Excellence in Functional Advanced Materials Engineering, Thammasat University
Zitieren
APA
Khimlek, W., Jindakeaw, J., Primpray, V., Karuwan, C., Tago, T., Sreearunothai, P., Kaewsaneha, C., Tuantranont, A., & Opaprakasit, P. (2026). Fabrication and Characterization of 3D-Printed Polylactide Composite Scaffolds with Modified Graphene. ACS Omega, 11(44), 68341-68353. https://doi.org/10.1021/acsomega.6c04916
Vancouver
Khimlek W, Jindakeaw J, Primpray V, Karuwan C, Tago T, Sreearunothai P, et al. Fabrication and Characterization of 3D-Printed Polylactide Composite Scaffolds with Modified Graphene. ACS Omega. 2026;11(44):68341-68353. doi:10.1021/acsomega.6c04916
BibTeX
@article{Khimlek2026,
author = {Khimlek, Worathep and Jindakeaw, Jirawan and Primpray, Vitsarut and Karuwan, Chanpen and Tago, Teruoki and Sreearunothai, Paiboon and Kaewsaneha, Chariya and Tuantranont, Adisorn and Opaprakasit, Pakorn},
title = {Fabrication and Characterization of 3D-Printed Polylactide Composite Scaffolds with Modified Graphene},
journal = {ACS Omega},
year = {2026},
volume = {11},
number = {44},
pages = {68341--68353},
doi = {10.1021/acsomega.6c04916}
}
EUVIMED