EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Modification of 3D Printable Polymer Filaments for Radiation Shielding Applications

Antonio Jreije iD, Swaroop Kumar Mutyala, Benas Gabrielis Urbonavičius, Aušrinė Šablinskaitė, Neringa Keršienė, Judita Puišo iD, Živilė Rutkūnienė, Diana Adlienė iD

Polymers · 29.03.2023 · 15 (7) · 1700

DOI: 10.3390/polym15071700 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 29.03.2023. Verfasst von Antonio Jreije und 7 weiteren Autor:innen. Beteiligte Einrichtung: Department of Physics, Kaunas University of Technology, Studentu˛ Str. 50, 51368 Kaunas, Lithuania. Die Arbeit wurde bisher 26-mal zitiert (Crossref) und nennt 46 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

There is a growing need to develop lead-free shielding materials that are safe, low weight, durable, environmentally friendly, chemically and mechanically stable and customizable for specific applications. Fused deposition modeling (FDM), an additive manufacturing technique based on the extrusion of a thermoplastic filament into a 3D printed object one layer at a time, could be employed well in applications involving ionizing radiation due to its relatively low cost, design flexibility and high manufacturing precision. This study aimed at developing 3D printing composites that contain Titanium dioxide as a filler agent for shielding in a medical radiation environment. First, the effect of low-dose ionizing radiation (up to 15 Gy) on the mechanical properties of common 3D printing polymers, ABS, ULTRAT, PLA, NYLON, ASA and PETG, was investigated. Since ABS experienced the lowest variation in its ultimate tensile strength (±5%) and Young’s modulus (−5%/+11%), it was chosen as a matrix for a new extruded 3D filament containing TiO2 at 1 wt.%, 3 wt.%, and 5 wt.%. With the incorporation of TiO2 at different filler contents, the UTS of the ABS composites varied between 24.1 MPa and 28.4 MPa, with the highest value recorded for 3 wt.% TiO2. Young’s modulus values were dependent on both the TiO2 concentration and on the irradiation dose. In addition, the ABS/TiO2 composites with a higher filler content (3 wt.% and 5 wt.%) maintained their attenuation ability even after exposure to a radiation dose of 100 Gy as opposed to pure ABS, which exhibited a ~2.5% reduction in its mass attenuation coefficient after exposure to the same dose of radiation. The pilot investigation performed demonstrated that the newly developed ABS/TiO2 composite containing 5 wt.% of filler can be successfully employed to shield electronic devices operating in a radiotherapy room.

Schlagwörter

Stichwörter der Autor:innen

3D printingfused deposition modelingionizing radiationpolymer compositesradiation shielding

Autor:innen und Institutionen

  • Department of Physics, Kaunas University of Technology, Studentu˛ Str. 50, 51368 Kaunas, Lithuania.

ORCID-Profile: Antonio Jreije, Judita Puišo, Diana Adlienė

Zitieren

APA

Jreije, A., Mutyala, S. K., Urbonavičius, B. G., Šablinskaitė, A., Keršienė, N., Puišo, J., Rutkūnienė, Ž., & Adlienė, D. (2023). Modification of 3D Printable Polymer Filaments for Radiation Shielding Applications. Polymers, 15(7), 1700. https://doi.org/10.3390/polym15071700

Vancouver

Jreije A, Mutyala SK, Urbonavičius BG, Šablinskaitė A, Keršienė N, Puišo J, et al. Modification of 3D Printable Polymer Filaments for Radiation Shielding Applications. Polymers. 2023;15(7):1700. doi:10.3390/polym15071700

BibTeX
@article{Jreije2023,
  author = {Jreije, Antonio and Mutyala, Swaroop Kumar and Urbonavičius, Benas Gabrielis and Šablinskaitė, Aušrinė and Keršienė, Neringa and Puišo, Judita and Rutkūnienė, Živilė and Adlienė, Diana},
  title = {Modification of 3D Printable Polymer Filaments for Radiation Shielding Applications},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {7},
  pages = {1700},
  doi = {10.3390/polym15071700}
}
Kostenlos starten →