EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Design of Polymeric 3D Printable Materials for THz Technology Applications

Beatrice Tosetto, Laura Pilozzi, Mauro Missori, Andrea Camellini iD, Tingwen M Guo, Candido Fabrizio Pirri, Yannis Laplace iD, Giancarlo Rizza iD, Ignazio Roppolo iD

ACS Applied Polymer Materials · 10.07.2026 · 8 (13) · 10702-10715

DOI: 10.1021/acsapm.6c01662 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Applied Polymer Materials, online erschienen am 25.06.2026. Verfasst von Beatrice Tosetto und 8 weiteren Autor:innen. Beteiligte Einrichtung: Department of Applied Science and Technology, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Turin, Italy. Die Arbeit nennt 70 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministero dell'Università e della Ricerca.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

High Resolution Image Download MS PowerPoint Slide Terahertz (THz) radiation is rapidly gaining attention for applications in biomedical diagnostics, security, and wireless communication. Polymers play a central role in advancing THz technologies, as they are ideal for lenses, filters, waveguides, and metasurfaces. However, material selection is driven by commercial availability rather than by the rational design of their composition, and progress is hindered by the limited availability of polymers that combine low THz losses with high printability. To address this problem, the relationship between polymer composition and THz transparency in photocurable resins is here investigated, establishing practical guidelines for tailoring THz response through resin composition. A comprehensive framework is developed to predict THz properties based on key structural features, including heteroatoms, cyclic structures, secondary forces, and the carbon-to-oxygen (C/O) ratio. In particular, (meth)acrylic resins with aliphatic backbones exhibit predictable behavior, enabling the estimation of their THz response directly from the C/O atomic ratio. Using the best-performing formulations, photonic crystals for THz modulation were fabricated via digital light processing (DLP) 3D printing. These devices are used to demonstrate how geometric parameters, fabrication precision, and material properties influence the THz devices’ response. Comparisons between THz-optimized formulations and commercial resins highlight the importance of combining high printability and THz transparency in the fabrication of functional devices, demonstrating that proper resin design enables the decrease of the absorption coefficient up to 5 cm –1 at 1THz (vs 19–30 cm –1 of commercial resins usually employed for 3D-printed THz devices), maintaining a sufficient printability, resulting in an extension of the range of controllable response of the photonic crystals up to 2 THz, well beyond the sub-0.5 THz limit typically reported in the literature for similar structures. This material-driven approach establishes a rational pathway for designing polymers tailored for THz applications while enabling the fabrication of technologically relevant devices with accessible and low-cost 3D printing.

Schlagwörter

Stichwörter der Autor:innen

3D printingadditive manufacturingdigital light processingphotocurable polymersphotonic crystalspolymersterahertz

Autor:innen und Institutionen

  • Department of Applied Science and Technology, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Turin, Italy.
  • Department of Chemistry, Biology and Biotechnology, University of Perugia, Via Elce di Sotto 8, 06123 Perugia, Italy.
  • Center for Sustainable Future Technologies, Italian Institute of Technology, Via Livorno 60, 10144 Turin, Italy.
  • Institute for Complex Systems, National Research Council (ISC-CNR), Via dei Taurini 19, 00185 Rome, Italy.
  • Laboratoire des Solides Irradiés, CEA/DRF/IRAMIS, Institut Polytechnique de Paris, CNRS, 91128 Palaiseau, France.

ORCID-Profile: Andrea Camellini, Yannis Laplace, Giancarlo Rizza, Ignazio Roppolo

Förderung

  • Ministero dell'Università e della Ricerca

Zitieren

APA

Tosetto, B., Pilozzi, L., Missori, M., Camellini, A., Guo, T. M., Pirri, C. F., Laplace, Y., Rizza, G., & Roppolo, I. (2026). Design of Polymeric 3D Printable Materials for THz Technology Applications. ACS Applied Polymer Materials, 8(13), 10702-10715. https://doi.org/10.1021/acsapm.6c01662

Vancouver

Tosetto B, Pilozzi L, Missori M, Camellini A, Guo TM, Pirri CF, et al. Design of Polymeric 3D Printable Materials for THz Technology Applications. ACS Applied Polymer Materials. 2026;8(13):10702-10715. doi:10.1021/acsapm.6c01662

BibTeX
@article{Tosetto2026,
  author = {Tosetto, Beatrice and Pilozzi, Laura and Missori, Mauro and Camellini, Andrea and Guo, Tingwen M and Pirri, Candido Fabrizio and Laplace, Yannis and Rizza, Giancarlo and Roppolo, Ignazio},
  title = {Design of Polymeric 3D Printable Materials for THz Technology Applications},
  journal = {ACS Applied Polymer Materials},
  year = {2026},
  volume = {8},
  number = {13},
  pages = {10702--10715},
  doi = {10.1021/acsapm.6c01662}
}
Kostenlos starten →