Tribological Properties of Glass Bead-Filled Polyamide 12 Composite Manufactured by Selective Laser Sintering
Polymers · 02.03.2023 · 15 (5) · 1268
DOI: 10.3390/polym15051268 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 02.03.2023. Verfasst von Abdelrasoul Gadelmoula und 1 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical and Industrial Engineering, College of Engineering, Majmaah University, Al-Majmaah 11952, Saudi Arabia. Die Arbeit wurde bisher 23-mal zitiert (Crossref) und nennt 36 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Deanship of Scientific Research at Majmaah University.
Abstract (Originalsprache)
To enhance the properties of polyamide 12 (PA12/Nylon 12) manufactured by the selective laser sintering (SLS) process, micron-sized glass beads are used as a filler, and the resulting composite is known as glass bead-filled PA12 (PA 3200 GF). Despite PA 3200 GF basically being a tribological-grade powder, very little has been reported on the tribological properties of laser-sintered objects based on this powder. As the properties of SLS objects are orientation-dependent, this study is devoted to investigating the friction and wear characteristics of the PA 3200 GF composite sliding against the steel disc in the dry-sliding mode. The test specimens were aligned in the SLS build chamber along five different orientations (X-axis, Y-axis, Z-axis, XY-plane, and YZ-plane). Additionally, the interface temperature and the friction-induced noise were measured. The pin-shaped specimens were examined using a pin-on-disc tribo-tester for 45 min to investigate the steady-state tribological characteristics of the composite material. The results revealed that the orientation of build layers relative to the sliding plane was a ruling parameter that determined the dominant wear pattern and the wear rate. Accordingly, where build layers were parallel or inclined to the sliding plane, abrasive wear predominated, and wear rate became 48% higher than that of specimens with perpendicular build layers, for which adhesive wear predominated. Interestingly, a noticeable synchronous variation of adhesion and friction-induced noise was observed. Taken together, the results from this study can efficiently serve the goals of fabricating SLS-functional parts with customized tribological properties.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Mechanical and Industrial Engineering, College of Engineering, Majmaah University, Al-Majmaah 11952, Saudi Arabia.
- Department of Mechanical Design and Production Engineering, Faculty of Engineering, Assiut University, Assiut 71515, Egypt.
ORCID-Profile: Abdelrasoul Gadelmoula, Saleh Ahmed Aldahash
Förderung
- Deanship of Scientific Research at Majmaah University
Zitieren
APA
Gadelmoula, A., & Aldahash, S. A. (2023). Tribological Properties of Glass Bead-Filled Polyamide 12 Composite Manufactured by Selective Laser Sintering. Polymers, 15(5), 1268. https://doi.org/10.3390/polym15051268
Vancouver
Gadelmoula A, Aldahash SA. Tribological Properties of Glass Bead-Filled Polyamide 12 Composite Manufactured by Selective Laser Sintering. Polymers. 2023;15(5):1268. doi:10.3390/polym15051268
BibTeX
@article{Gadelmoula2023,
author = {Gadelmoula, Abdelrasoul and Aldahash, Saleh Ahmed},
title = {Tribological Properties of Glass Bead-Filled Polyamide 12 Composite Manufactured by Selective Laser Sintering},
journal = {Polymers},
year = {2023},
volume = {15},
number = {5},
pages = {1268},
doi = {10.3390/polym15051268}
}
EUVIMED