EUVIMEDEUVIMED entdecken
Open Access

On the Difference in Mechanical Behavior of Glass Bead-Filled Polyamide 12 Specimens Produced by Laser Sintering and Injection Molding

Hellen De Coninck iD, Sebastian Meyers, Peter Van Puyvelde, Brecht Van Hooreweder iD

3D Printing and Additive Manufacturing · 01.04.2024 · 11 (2) · 419-433

DOI: 10.1089/3dp.2022.0160 ↗

Kurz gefasst

Fachartikel in der Zeitschrift 3D Printing and Additive Manufacturing, online erschienen am 16.04.2024. Verfasst von Hellen De Coninck und 3 weiteren Autor:innen. Beteiligte Einrichtung: KU Leuven, Department of Mechanical Engineering, Manufacturing Processes and Systems (MaPS), Leuven, Belgium. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 32 Literaturangaben. Der Volltext ist frei in PubMed Central verfügbar.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

An increasing demand for additively manufactured polymer composites with optimized mechanical properties is manifesting in different industries such as aerospace, biomedical, and automotive. Laser sintering (LS) is an additive manufacturing method that has the potential to produce reinforced polymers, which can meet the stringent requirements of these industries. For the development of a commercially viable LS nylon-based composite material, previous research studies worldwide have focused on adding glass beads to the powder material with the goal to produce fully dense parts with properties more representative of injection molded (IM) thermoplastic composites. This led to the development of a commercially available glass bead-filled polyamide 12 (PA12) powder. Although this powder has been on the market for quite a while, an in-depth comparison of the mechanical behavior of laser sintered versus IM glass bead-filled PA12 is lacking. In this study, laser-sintered glass bead-filled PA12 samples were built in different orientations and compared to IM counterparts. After sample production, the mechanical performance of the produced LS and IM parts was tested and compared to evaluate the quasistatic and dynamic mechanical performance and failure mechanisms at different load levels. In addition, the glass bead-filled PA12 properties were also compared to those of standard (unfilled) LS PA12 to assess whether glass beads actually improve the mechanical performance and fatigue lifetime of the final LS samples, as suggested in literature. Results in this work present and explain the increased stiffness but decreased fatigue life of glass bead-filled polyamide parts made by LS and IM. This research can be regarded as a “benchmark” study, in which samples produced from commercially available, filled and unfilled, PA12 powder grades are compared for both LS and conventional production techniques.

Schlagwörter

Stichwörter der Autor:innen

fatigue performancefilled polymersinjection moldinglaser sinteringpolyamide 12

Autor:innen und Institutionen

  • KU Leuven, Department of Mechanical Engineering, Manufacturing Processes and Systems (MaPS), Leuven, Belgium.
  • KU Leuven, Department of Chemical Engineering, Soft Matter, Rheology and Technology (SMaRT), Leuven, Belgium.

ORCID-Profile: Hellen De Coninck, Brecht Van Hooreweder

Zitieren

APA

De Coninck, H., Meyers, S., Van Puyvelde, P., & Van Hooreweder, B. (2024). On the Difference in Mechanical Behavior of Glass Bead-Filled Polyamide 12 Specimens Produced by Laser Sintering and Injection Molding. 3D Printing and Additive Manufacturing, 11(2), 419-433. https://doi.org/10.1089/3dp.2022.0160

Vancouver

De Coninck H, Meyers S, Van Puyvelde P, Van Hooreweder B. On the Difference in Mechanical Behavior of Glass Bead-Filled Polyamide 12 Specimens Produced by Laser Sintering and Injection Molding. 3D Printing and Additive Manufacturing. 2024;11(2):419-433. doi:10.1089/3dp.2022.0160

BibTeX
@article{DeConinck2024,
  author = {De Coninck, Hellen and Meyers, Sebastian and Van Puyvelde, Peter and Van Hooreweder, Brecht},
  title = {On the Difference in Mechanical Behavior of Glass Bead-Filled Polyamide 12 Specimens Produced by Laser Sintering and Injection Molding},
  journal = {3D Printing and Additive Manufacturing},
  year = {2024},
  volume = {11},
  number = {2},
  pages = {419--433},
  doi = {10.1089/3dp.2022.0160}
}
Kostenlos starten →