EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of Build Orientation and Part Thickness on Tensile Properties of Polyamide 12 Parts Manufactured by Selective Laser Sintering

Jonathan J Slager iD, Brian C Earp iD, Ahmed M Ibrahim iD

Polymers · 07.08.2024 · 16 (16) · 2241

DOI: 10.3390/polym16162241 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 07.08.2024. Verfasst von Jonathan J Slager und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical and Nuclear Engineering, United States Naval Academy, Annapolis, MD 21401, USA. Die Arbeit wurde bisher 21-mal zitiert (Crossref) und nennt 37 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Office of Naval Research, Office of Naval Research (ONR) research project, structural reliability portfolio.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The use of additive manufacturing to rapidly test and evaluate solutions to engineering problems has been demonstrated. Selective laser sintering (SLS) is a subset of additive manufacturing that is particularly well suited to producing structural thin wall models and end use parts which can improve the ability to prototype and manufacture certain designs at a substantially lower cost and time compared to current methods. However, a more comprehensive understanding of the material properties of these parts is warranted. The presented research investigates the influence of print orientation and sample thickness on the material properties of printed SLS parts. This novel work involves holding a hatch pattern constant across SLS prints using polyamide 12 material to isolate the anisotropic effects of orientation and thickness. An evaluation of ultimate tensile strength, modulus of elasticity, strain at failure, yield strength, and Poisson’s ratio, and scanning electron microscope fractography are conducted. Transverse strain and Poisson’s ratio are a key aspect that provide insight into the feasibility of building numerical orthotropic models. These data are used to calculate the degree of anisotropy due to both thickness and orientation. The results support the future use of SLS printing and modeling of thin-walled structures, such as scaled structural ship modeling. The presented data provide guidance on the impact of print orientation and thickness that will aid in manufacturing structural parts with intentionally tuned material properties.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturing (AM)modelingorientation and thickness affectsorthotropicpolyamide-12 (PA12)selective laser sintering (SLS)

Autor:innen und Institutionen

  • Department of Mechanical and Nuclear Engineering, United States Naval Academy, Annapolis, MD 21401, USA.
  • Department of Naval Architecture and Ocean Engineering, United States Naval Academy, Annapolis, MD 21401, USA.

ORCID-Profile: Jonathan J Slager, Brian C Earp, Ahmed M Ibrahim

Förderung

  • Office of Naval Research
  • Office of Naval Research (ONR) research project
  • structural reliability portfolio

Zitieren

APA

Slager, J. J., Earp, B. C., & Ibrahim, A. M. (2024). Influence of Build Orientation and Part Thickness on Tensile Properties of Polyamide 12 Parts Manufactured by Selective Laser Sintering. Polymers, 16(16), 2241. https://doi.org/10.3390/polym16162241

Vancouver

Slager JJ, Earp BC, Ibrahim AM. Influence of Build Orientation and Part Thickness on Tensile Properties of Polyamide 12 Parts Manufactured by Selective Laser Sintering. Polymers. 2024;16(16):2241. doi:10.3390/polym16162241

BibTeX
@article{Slager2024,
  author = {Slager, Jonathan J and Earp, Brian C and Ibrahim, Ahmed M},
  title = {Influence of Build Orientation and Part Thickness on Tensile Properties of Polyamide 12 Parts Manufactured by Selective Laser Sintering},
  journal = {Polymers},
  year = {2024},
  volume = {16},
  number = {16},
  pages = {2241},
  doi = {10.3390/polym16162241}
}
Kostenlos starten →