A Low-Cost Process for Fabricating Reinforced 3D Printing Thermoplastic Filaments
Polymers · 07.01.2023 · 15 (2) · 315
DOI: 10.3390/polym15020315 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 07.01.2023. Verfasst von Mohamed Hassanien und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, American University of Sharjah, Sharjah P.O. Box 26666, United Arab Emirates. Die Arbeit wurde bisher 11-mal zitiert (Crossref) und nennt 42 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: American University of Sharjah, American University of Sharjah, United Arab Emirates, through the Office of Research, Open Access Program at the American University of Sharjah.
Abstract (Originalsprache)
Low-cost desktop-sized fused deposition modeling (FDM) printers have been widely embraced by small to large-scale institutions and individuals. To further enhance their utility and increase the range of materials that they can process, this work proposes a low-cost solution that adapts to low-cost desktop-sized extruders and enables them to fabricate filaments comprising a wide range of nonorganic reinforcing particles. This solution will fill a gap in the field, as low-cost fabrication techniques for reinforced filaments have been lacking. In the proposed solution, particles are heated and deposited on thermoplastic pellets to form a coating. Coated pellets are subsequently extruded using a low-cost desktop single-screw extruder. The effectiveness of the process is demonstrated by fabricating polylactic acid (PLA) filaments reinforced with two types of reinforcements, namely, dune sand and silicon carbide. Filaments’ stiffness and strength were measured, and their microstructure along their lateral and longitudinal directions were investigated. Improvements in tensile strength (up to 8%) and stiffness (up to 4.5%) were observed, but at low reinforcement levels (less than 2 wt%). Results showed that the proposed process could be used to fabricate filaments with multiple types of particles. The produced filaments were successfully used to fabricate 3D parts using a commercial desktop FDM printer.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Mechanical Engineering, American University of Sharjah, Sharjah P.O. Box 26666, United Arab Emirates.
ORCID-Profile: Mohamed Hassanien, Maen Alkhader, Bassam A Abu-Nabah, Wael Abuzaid
Förderung
- American University of Sharjah
- American University of Sharjah, United Arab Emirates, through the Office of Research
- Open Access Program at the American University of Sharjah
Zitieren
APA
Hassanien, M., Alkhader, M., Abu-Nabah, B. A., & Abuzaid, W. (2023). A Low-Cost Process for Fabricating Reinforced 3D Printing Thermoplastic Filaments. Polymers, 15(2), 315. https://doi.org/10.3390/polym15020315
Vancouver
Hassanien M, Alkhader M, Abu-Nabah BA, Abuzaid W. A Low-Cost Process for Fabricating Reinforced 3D Printing Thermoplastic Filaments. Polymers. 2023;15(2):315. doi:10.3390/polym15020315
BibTeX
@article{Hassanien2023,
author = {Hassanien, Mohamed and Alkhader, Maen and Abu-Nabah, Bassam A and Abuzaid, Wael},
title = {A Low-Cost Process for Fabricating Reinforced 3D Printing Thermoplastic Filaments},
journal = {Polymers},
year = {2023},
volume = {15},
number = {2},
pages = {315},
doi = {10.3390/polym15020315}
}
EUVIMED