EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Comparison of Flexural Strength, Hardness, and Surface Roughness of Heat-Cured and 3D-Printed Acrylic Resin Materials After Immersion in Different Disinfectants: An In Vitro Comparative Study

Sanar A. Khasraw, Jwan F. Abdulkareem

Oral · 14.10.2025 · 5 (4) · 81

DOI: 10.3390/oral5040081 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Oral, online erschienen am 14.10.2025. Verfasst von Sanar A. Khasraw und 1 weiteren Autor:innen. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 72 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objective

The purpose of this study was to compare the flexural strength, flexural modulus, hardness, and surface roughness of one brand each of 3D-printed and heat-cured acrylic resin materials after they were immersed in various disinfection solutions.

Methods

The study included 160 specimens, consisting of 80 heat-cured and 80 3D-printed specimens. Forty specimens of each resin material type were prepared for flexural testing, while an additional forty specimens were designated for hardness and surface roughness assessments. Each collection of 40 specimens was subsequently randomized into four subgroups (n = 10) for immersion in either distilled water (control), 1% sodium hypochlorite, Superdent, or Kin Oro denture cleansers. Flexural test, hardness, and surface roughness assessments were performed. Data analysis was conducted using SPSS, with a level of significance set at p < 0.05.

Results

Flexural strength and surface roughness did not differ significantly between the two resin types. Flexural modulus was significantly higher in the heat-cured resin among all the disinfectants (p = 0.000). The heat-cured resin had significantly higher microhardness than the 3D-printed resin among the disinfectants except for the Kin Oro group, and both resins showed a significant reduction in hardness after immersion in disinfectants compared to distilled water (p < 0.05).

Conclusions

The heat-cured resin demonstrated higher flexural modulus and surface hardness compared to the 3D-printed resin. Flexural strength and surface roughness were comparable between the two materials. Both resins had their highest mechanical properties in distilled water.

Zitieren

APA

Khasraw, S. A., & Abdulkareem, J. F. (2025). Comparison of Flexural Strength, Hardness, and Surface Roughness of Heat-Cured and 3D-Printed Acrylic Resin Materials After Immersion in Different Disinfectants: An In Vitro Comparative Study. Oral, 5(4), 81. https://doi.org/10.3390/oral5040081

Vancouver

Khasraw SA, Abdulkareem JF. Comparison of Flexural Strength, Hardness, and Surface Roughness of Heat-Cured and 3D-Printed Acrylic Resin Materials After Immersion in Different Disinfectants: An In Vitro Comparative Study. Oral. 2025;5(4):81. doi:10.3390/oral5040081

BibTeX
@article{Khasraw2025,
  author = {Khasraw, Sanar A. and Abdulkareem, Jwan F.},
  title = {Comparison of Flexural Strength, Hardness, and Surface Roughness of Heat-Cured and 3D-Printed Acrylic Resin Materials After Immersion in Different Disinfectants: An In Vitro Comparative Study},
  journal = {Oral},
  year = {2025},
  volume = {5},
  number = {4},
  pages = {81},
  doi = {10.3390/oral5040081}
}
Kostenlos starten →