EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Effects of post‐polymerization conditions on color properties, surface roughness, and flexural strength of 3D‐printed permanent resin material after thermal aging

Simge Baytur, Almira Ada Diken Turksayar iD

Journal of Prosthodontics · 2025-03 · 34 (3) · 298-307

DOI: 10.1111/jopr.13818 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, online erschienen am 12.01.2024. Verfasst von Simge Baytur und 1 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Faculty of Dentistry, Beykent University, Istanbul, Turkey. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Flexural Strength, Dental Materials, Crowns. Die Arbeit wurde bisher 35-mal zitiert (Crossref) und nennt 34 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

To evaluate the color, surface properties, and flexural strength of 3D‐printed permanent crown resin subjected to different post‐polymerization conditions after artificial aging. Materials and Methods Ninety (10 × 2 mm) disc‐shaped specimens were printed by using permanent crown resin with SLA technology. Specimens were divided into nine different groups, subject to post‐polymerization conditions at three different times (15, 20, and 30 min) and three different temperatures (40, 60, and 80°C) ( n = 10). Color and surface roughness measurements were repeated pre‐post thermal aging (5.000 cycles, 5–55°C) and a flexural strength test was carried out. Data were analyzed with Shapiro–Wilk, Kruskal–Wallis, ANOVA, Tukey HSD, and Dunn tests (α < 0.05).

Results

ΔE 00 values showed results below the acceptable color threshold, except for the 30 min 40°C group (ΔE 00

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalFlexural StrengthDental MaterialsCrownsSurface PropertiesPolymerizationColorMaterials TestingTemperatureTime Factors

Stichwörter der Autor:innen

dental materialsin vitro testpermanentthree‐dimensional printing

Substanzen

Dental Materials

Autor:innen und Institutionen

  • Department of Prosthodontics, Faculty of Dentistry, Beykent University, Istanbul, Turkey.
  • Department of Prosthodontics, Faculty of Dentistry, Biruni University, Istanbul, Turkey.
  • ADMiRE Research Center-Additive Manufacturing, Intelligent Robotics, Sensors and Engineering, School of Engineering and IT, Carinthia University of Applied Sciences, Villach, Austria.

ORCID-Profile: Almira Ada Diken Turksayar

Zitieren

APA

Baytur, S., & Diken Turksayar, A. A. (2025). Effects of post‐polymerization conditions on color properties, surface roughness, and flexural strength of 3D‐printed permanent resin material after thermal aging. Journal of Prosthodontics, 34(3), 298-307. https://doi.org/10.1111/jopr.13818

Vancouver

Baytur S, Diken Turksayar AA. Effects of post‐polymerization conditions on color properties, surface roughness, and flexural strength of 3D‐printed permanent resin material after thermal aging. Journal of Prosthodontics. 2025;34(3):298-307. doi:10.1111/jopr.13818

BibTeX
@article{Baytur2025,
  author = {Baytur, Simge and Diken Turksayar, Almira Ada},
  title = {Effects of post‐polymerization conditions on color properties, surface roughness, and flexural strength of 3D‐printed permanent resin material after thermal aging},
  journal = {Journal of Prosthodontics},
  year = {2025},
  volume = {34},
  number = {3},
  pages = {298--307},
  doi = {10.1111/jopr.13818}
}
Kostenlos starten →