Multi-Objective Optimization of Mechanical and Geometric Properties of 3D-Printed PLA Porous Scaffolds for Biomedical Applications
Materials · 05.03.2026 · 19 (5) · 1008
DOI: 10.3390/ma19051008 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 05.03.2026. Verfasst von Alejandro González González und 4 weiteren Autor:innen. Beteiligte Einrichtung: Centro de Estudio de Fabricación Avanzada y Sostenible (CEFAS), Universidad de Matanzas, Matanzas 40100, Cuba. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 125 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
Porous scaffolds fabricated via fused deposition modeling (FDM) are promising for bone tissue engineering, but their mechanical performance and geometric fidelity are governed by complex interactions between process parameters and architectural design. This study presents a multi-objective optimization framework for poly (lactic acid) (PLA) scaffolds based on three triply periodic minimal surface (TPMS) topologies—Gyroid, Primitive, and Diamond. A Box–Behnken design combined with response surface methodology was used to model compressive strength, elastic modulus, yield strength, energy absorption density, and discrepancies in volume and porosity as functions of layer thickness (0.05–0.15 mm), extrusion temperature (210–220 °C), and target porosity (50–70%). The resulting quadratic models exhibited strong predictive capability (R2 > 77%, with most >90%) and were validated experimentally at extreme parameter combinations, yielding relative errors below 10% for 83% of measurements. Multi-objective optimization using NSGA-II, coupled with principal component analysis and correlation-based objective reduction, revealed that the six original objectives collapse to topology-specific essential pairs: absorbed energy density and porosity discrepancy for Gyroid; Young’s modulus and volume discrepancy for Primitive; and Young’s modulus and porosity discrepancy for Diamond. The generated Pareto fronts quantify the inherent trade-off between mechanical performance and geometric fidelity for each topology, providing designers with explicit decision maps. This framework enables rational, application-driven selection of printing parameters and scaffold architecture, advancing the clinical translation of patient-specific FDM-printed bone scaffolds.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Centro de Estudio de Fabricación Avanzada y Sostenible (CEFAS), Universidad de Matanzas, Matanzas 40100, Cuba.
- Centro de Innovación e Investigación en Ingeniería Aeronáutica, Facultad de Ingeniería Mecánica y Eléctrica, Universidad Autónoma de Nuevo León, San Nicolás de los Garza 66455, NL, Mexico.
- Escuela Politécnica Superior de Ingeniería, Universidad de La Laguna (ULL), Avenida Ángel Guimerá Jorge, s/n. 456-38200, 38200 Santa Cruz de Tenerife, Tenerife, Spain.
ORCID-Profile: Alejandro González González, Patricia C Zambrano-Robledo, Deivis Avila, Ramón Quiza
Zitieren
APA
González González, A., Zambrano-Robledo, P. C., Avila, D., Rivas, M., & Quiza, R. (2026). Multi-Objective Optimization of Mechanical and Geometric Properties of 3D-Printed PLA Porous Scaffolds for Biomedical Applications. Materials, 19(5), 1008. https://doi.org/10.3390/ma19051008
Vancouver
González González A, Zambrano-Robledo PC, Avila D, Rivas M, Quiza R. Multi-Objective Optimization of Mechanical and Geometric Properties of 3D-Printed PLA Porous Scaffolds for Biomedical Applications. Materials. 2026;19(5):1008. doi:10.3390/ma19051008
BibTeX
@article{GonzlezGonzlez2026,
author = {González González, Alejandro and Zambrano-Robledo, Patricia C and Avila, Deivis and Rivas, Marcelino and Quiza, Ramón},
title = {Multi-Objective Optimization of Mechanical and Geometric Properties of 3D-Printed PLA Porous Scaffolds for Biomedical Applications},
journal = {Materials},
year = {2026},
volume = {19},
number = {5},
pages = {1008},
doi = {10.3390/ma19051008}
}
EUVIMED