Design and Characterization of 3D Printed Auxetic PLA-HA Composite Scaffolds for Biomedical Application
Materials · 10.05.2026 · 19 (10) · 1972
DOI: 10.3390/ma19101972 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 10.05.2026. Verfasst von Mohammed Amine Benziada und 6 weiteren Autor:innen. Beteiligte Einrichtung: Laboratory of Materials Sciences and Engineering (LSGM), University of Sciences and Technology Houari Boumediene, Bab Ezzouar, Algiers 16111, Algeria. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 78 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Agencia Estatal de Investigación, Dirección General de Universidades e Investigación.
Abstract (Originalsprache)
Additive manufacturing (AM) techniques are becoming key factors for repairing and replacing damaged bone. These techniques enable the customization of implants, which can be tailored to the specific area to be treated or healed. Additionally, the combination of absorbable and osteoconductive biomaterials with 3D printing could eliminate second surgeries to remove implants, which is particularly relevant in pediatric and geriatric patients. The capabilities of AM in this context affect not only the external shape but also the internal microarchitecture, where the arrangement of struts to develop complex infills enhances relevant properties such as specific strength, degradation rate, and vascularization. In this study, auxetic scaffold structures made of both polylactic acid (PLA) and a PLA-hydroxyapatite (PLA-HA) composite with 40 wt% of hydroxyapatite (HA) are designed and produced using Fused Filament Fabrication (FFF). Samples of PLA and PLA-HA were 3D printed in dense samples and with auxetic infills. In dense samples, the characterization is performed by X-ray diffraction (XRD), Raman spectroscopy, wettability tests, nanoindentation, and tribological assessments. Two auxetic cellular models have been tested after degradation in PBS media, and their microstructural, structural, and mechanical properties are analyzed. Results show that the addition of hydroxyapatite (HA) significantly improves the hydrophilicity of the PLA matrix, as evidenced by a decrease in water contact angle from 73.4 ± 4.4° to 52.6 ± 2.8° (≈28% reduction), while also enhancing its mechanical and tribological properties, with hardness increasing from 207 ± 30 MPa to 241 ± 28 MPa (≈15%) and Young’s modulus from 4.08 ± 0.55 GPa to 6.24 ± 0.61 GPa (≈53%). Additionally, biodegradation of PLA-HA composites reveals a significant reduction in mechanical properties after 15 days, while the auxetic re-entrant structures mostly retain their shape during compression testing.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Laboratory of Materials Sciences and Engineering (LSGM), University of Sciences and Technology Houari Boumediene, Bab Ezzouar, Algiers 16111, Algeria.
- Instituto de Ceramica y Vidrio (ICV-CSIC), Calle Kelsen 5, 28049 Madrid, Spain.
- Centre d'Integritat Estructural, Fiabilitat i Micromecànica dels Materials (CIEFMA-UPC), Department of Materials Science and Engineering, Universitat Politècnica de Catalunya-BarcelonaTech, Campus Diagonal Besòs-EEBE, 0…
- Barcelona Research Center in Multiscale Science and Engineering, Universitat Politècnica de Catalunya-BarcelonaTech, Campus Diagonal Besòs, 08019 Barcelona, Spain.
ORCID-Profile: Mohammed Amine Benziada, Antonio Javier Sanchez-Herencia, Ismail Daoud, Hossein Besharatloo, Begoña Ferrari, Ana Ferrandez-Montero
Förderung
- Agencia Estatal de Investigación
- Dirección General de Universidades e Investigación
Zitieren
APA
Benziada, M. A., Sanchez-Herencia, A. J., Daoud, I., Besharatloo, H., Ferrari, B., Miroud, D., & Ferrandez-Montero, A. (2026). Design and Characterization of 3D Printed Auxetic PLA-HA Composite Scaffolds for Biomedical Application. Materials, 19(10), 1972. https://doi.org/10.3390/ma19101972
Vancouver
Benziada MA, Sanchez-Herencia AJ, Daoud I, Besharatloo H, Ferrari B, Miroud D, et al. Design and Characterization of 3D Printed Auxetic PLA-HA Composite Scaffolds for Biomedical Application. Materials. 2026;19(10):1972. doi:10.3390/ma19101972
BibTeX
@article{Benziada2026,
author = {Benziada, Mohammed Amine and Sanchez-Herencia, Antonio Javier and Daoud, Ismail and Besharatloo, Hossein and Ferrari, Begoña and Miroud, Djamel and Ferrandez-Montero, Ana},
title = {Design and Characterization of 3D Printed Auxetic PLA-HA Composite Scaffolds for Biomedical Application},
journal = {Materials},
year = {2026},
volume = {19},
number = {10},
pages = {1972},
doi = {10.3390/ma19101972}
}
EUVIMED