EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Multi-Objective Optimization of the Mechanical Properties of 3D-Printed PLA: An Integrated Taguchi and NSGA-II Approach

Zainab Hussein Mohsein, Diana Abed Alkareem Noori, Aseel Hamad Abed iD, Abbas Fadhil Ibrahim, Osama M Irfan, Abdulrahman Mohammed Albar, Walid M Shewakh iD

Polymers · 25.07.2026 · 18 (15) · 1821

DOI: 10.3390/polym18151821 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 25.07.2026. Verfasst von Zainab Hussein Mohsein und 6 weiteren Autor:innen. Beteiligte Einrichtung: College of Production Engineering and Metallurgy, University of Technology, Baghdad 10066, Iraq. Die Arbeit nennt 48 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Qassim University, Deanship of Graduate Studies and Scientific Research at Qassim University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Fused deposition modeling (FDM) of polylactic acid (PLA) is widely used, yet most parameter studies tune one mechanical property at a time and leave the conflicts between properties unresolved. This work treats three responses of FDM PLA together: ultimate tensile strength, flexural strength, and Shore D hardness. A Taguchi L9 orthogonal array varied infill density, raster angle, and layer thickness; signal-to-noise ratios and analysis of variance ranked the factors, linear regression linked the parameters to each response, and the NSGA-II algorithm mapped the trade-off surface between them. Layer thickness proved the leading factor for tensile and flexural strength, while hardness answered mainly to infill density; raster angle stayed weak for every response. The Pareto front showed that low infill favors tensile strength while high infill favors flexural strength and hardness, all at the finest layer setting, and these trends were converted into parameter guidelines for tensile-led, flexure-led, and balanced parts. The statistical limits of the screening design are stated openly, the flexural and hardness campaigns are flagged as provisional, and a replicated, standard-compliant confirmation study is set out as the next step.

Schlagwörter

Stichwörter der Autor:innen

NSGA-IITaguchi methodadditive manufacturingfused deposition modelingmechanical propertiesmulti-objective optimizationpolylactic acid

Autor:innen und Institutionen

  • College of Production Engineering and Metallurgy, University of Technology, Baghdad 10066, Iraq.
  • Department of Mechanical Engineering, College of Engineering, Qassim University, Buraydah 51452, Saudi Arabia.
  • Department of Industrial Engineering, Jazan University, Jazan 82817, Saudi Arabia.

ORCID-Profile: Aseel Hamad Abed, Walid M Shewakh

Förderung

  • Qassim University
  • Deanship of Graduate Studies and Scientific Research at Qassim University

Zitieren

APA

Mohsein, Z. H., Noori, D. A. A., Abed, A. H., Ibrahim, A. F., Irfan, O. M., Albar, A. M., & Shewakh, W. M. (2026). Multi-Objective Optimization of the Mechanical Properties of 3D-Printed PLA: An Integrated Taguchi and NSGA-II Approach. Polymers, 18(15), 1821. https://doi.org/10.3390/polym18151821

Vancouver

Mohsein ZH, Noori DAA, Abed AH, Ibrahim AF, Irfan OM, Albar AM, et al. Multi-Objective Optimization of the Mechanical Properties of 3D-Printed PLA: An Integrated Taguchi and NSGA-II Approach. Polymers. 2026;18(15):1821. doi:10.3390/polym18151821

BibTeX
@article{Mohsein2026,
  author = {Mohsein, Zainab Hussein and Noori, Diana Abed Alkareem and Abed, Aseel Hamad and Ibrahim, Abbas Fadhil and Irfan, Osama M and Albar, Abdulrahman Mohammed and Shewakh, Walid M},
  title = {Multi-Objective Optimization of the Mechanical Properties of 3D-Printed PLA: An Integrated Taguchi and NSGA-II Approach},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {15},
  pages = {1821},
  doi = {10.3390/polym18151821}
}
Kostenlos starten →