EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Enhanced Mechanical and Surface Performance of Three-Dimensionally Printed Denture Base Resin via Zinc Oxide and Samarium Oxide Nanoparticle Reinforcement

Mohammed A Alsmael, Sabreen Waleed Ibrahim, Mohammed Hussein M Alsharbaty, Sameh S Ali iD, Michael Schagerl iD

Materials · 24.02.2026 · 19 (5) · 830

DOI: 10.3390/ma19050830 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 24.02.2026. Verfasst von Mohammed A Alsmael und 4 weiteren Autor:innen. Beteiligte Einrichtung: Prosthodontics Department, College of Dentistry, Al Muthana University, Samawah 66001, Iraq. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 52 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The increasing adoption of digital light processing (DLP) three-dimensional (3D) printing in prosthodontics has enabled the rapid fabrication of denture bases with improved dimensional accuracy and reproducibility. However, the mechanical performance and surface characteristics of 3D-printed denture base resins remain inferior to those of conventional heat-polymerized polymethyl methacrylate (PMMA), limiting their long-term clinical reliability. This study aimed to investigate the effect of incorporating zinc oxide (ZnO) and samarium oxide (Sm2O3) nanoparticles, individually and as hybrid nanofiller systems, on the mechanical and wettability properties of a DLP 3D-printed denture base resin. ZnO and Sm2O3 nanoparticles were incorporated into a photopolymerizable denture base resin at concentrations of 1 and 2 wt.%, producing seven experimental formulations, including a control group. A total of 280 specimens were fabricated using a DLP 3D printer and subjected to standardized post-processing. Nanoparticle dispersion and morphology were examined using field-emission scanning electron microscopy (FE-SEM), while Fourier-transform infrared spectroscopy (FTIR) was employed to assess possible chemical interactions between the nanofillers and the polymer matrix. Mechanical performance was evaluated through impact strength, transverse strength, and flexural strength tests, and surface wettability was assessed using static water contact angle measurements. Statistical analysis was conducted using one-way ANOVA followed by Tukey’s post hoc test (α = 0.05). The results demonstrated that all nanoparticle-reinforced groups exhibited significantly enhanced mechanical properties compared with the unmodified control resin. The incorporation of 1 wt.% nanofillers yielded the most pronounced improvements, with the 1 wt.% ZnO group achieving the highest transverse strength and the 1 wt.% ZnO–Sm2O3 hybrid group exhibiting the maximum flexural strength. Increasing the nanofiller concentration to 2 wt.% resulted in partial reductions in impact and flexural strength, which were attributed to nanoparticle agglomeration and increased light scattering during photopolymerization. FTIR analysis revealed no evidence of chemical bonding between the resin matrix and the nanofillers, indicating that the observed enhancements were primarily governed by physical reinforcement mechanisms. Wettability analysis showed that Sm2O3-containing formulations significantly reduced the water contact angle, indicating increased surface hydrophilicity, whereas ZnO incorporation produced more hydrophobic surfaces. Within the limitations of this in vitro study, the findings suggest that low-concentration incorporation of ZnO and Sm2O3 nanoparticles represents an effective strategy to enhance the mechanical integrity and tailor the surface properties of DLP 3D-printed denture base resins. These results suggest potential clinical relevance of nanoparticle-reinforced printed denture bases, emphasizing the importance of optimized filler loading to avoid agglomeration-induced performance degradation.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturingdenture base resinmechanical propertiespolymer nanocompositessamarium oxide nanoparticleszinc oxide nanoparticles

Autor:innen und Institutionen

  • Prosthodontics Department, College of Dentistry, Al Muthana University, Samawah 66001, Iraq.
  • Prosthodontics Department, College of Dentistry, Al Mustansiriyah University, Baghdad 10001, Iraq.
  • Branch of Prosthodontics, College of Dentistry, University of Al-Ameed, Karbala 56001, Iraq.
  • Botany and Microbiology Department, Faculty of Science, Tanta University, Tanta 31527, Egypt.
  • Department of Functional and Evolutionary Ecology, University of Vienna, Djerassiplatz 1, A-1030 Vienna, Austria.

ORCID-Profile: Sameh S Ali, Michael Schagerl

Zitieren

APA

Alsmael, M. A., Ibrahim, S. W., Alsharbaty, M. H. M., Ali, S. S., & Schagerl, M. (2026). Enhanced Mechanical and Surface Performance of Three-Dimensionally Printed Denture Base Resin via Zinc Oxide and Samarium Oxide Nanoparticle Reinforcement. Materials, 19(5), 830. https://doi.org/10.3390/ma19050830

Vancouver

Alsmael MA, Ibrahim SW, Alsharbaty MHM, Ali SS, Schagerl M. Enhanced Mechanical and Surface Performance of Three-Dimensionally Printed Denture Base Resin via Zinc Oxide and Samarium Oxide Nanoparticle Reinforcement. Materials. 2026;19(5):830. doi:10.3390/ma19050830

BibTeX
@article{Alsmael2026,
  author = {Alsmael, Mohammed A and Ibrahim, Sabreen Waleed and Alsharbaty, Mohammed Hussein M and Ali, Sameh S and Schagerl, Michael},
  title = {Enhanced Mechanical and Surface Performance of Three-Dimensionally Printed Denture Base Resin via Zinc Oxide and Samarium Oxide Nanoparticle Reinforcement},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {5},
  pages = {830},
  doi = {10.3390/ma19050830}
}
Kostenlos starten →