EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Mechanical properties of 3D printed denture base polymers

Andrea Coldea, Felicitas Mayinger, John Meinen, Moritz Hoffmann, Bogna Stawarczyk

The Journal of Prosthetic Dentistry · 2025-05 · 133 (5) · 1361.e1-1361.e8

DOI: 10.1016/j.prosdent.2025.02.009 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2025-05. Verfasst von Andrea Coldea und 4 weiteren Autor:innen. Beteiligte Einrichtung: Research Associate, Material Science Unit, Department of Prosthetic Dentistry, University Hospital, LMU Munich, Germany. Electronic address: andrea.c…. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Denture Bases, Polymers. Die Arbeit wurde bisher 16-mal zitiert (Crossref) und nennt 23 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: Studies on the mechanical properties of 3-dimensionally (3D) printed denture base polymers with appropriate test methods are lacking. PURPOSE: The purpose of this in vitro study was to determine the flexural strength (σf), elastic modulus (E), fracture toughness (KIC), work of fracture (ωe), and Martens hardness (HM) of 3D printed denture base polymers and to compare them with an injection molded material. MATERIAL AND METHODS: Three resins for additive (Lucitone Digital Print, LDP; Flexcera Base, FCB and an experimental material, EXP) and 1 for injection molding (IvoBase Hybrid, IBH) fabrication were analyzed. Standardized specimens were fabricated, polished, tempered, and thermal cycled (5 °C to 55 °C) before testing for σf, E, KIC, ωe, and HM. The results were explored by global analysis (α=.05). The Kolmogorov-Smirnov test was used to test for data distribution. Parametric and nonparametric tests followed by pairwise comparison were applied to test for differences between groups. RESULTS: The σf, E, and HM of 3D printed polymers were significantly lower than those of the injection molded, both for the tempered and aged groups. The σf was lowest for FCB and highest for IBH in the tempered state. The KIC and ωe of the tempered EXP and IBH groups were lower compared with those of FCB and LDP. After aging, EXP, FCB, and IBH presented KIC in the same range, but it was lower than for LDP. Compared with the printable polymers, the control group IBH was not affected by artificial aging. CONCLUSIONS: The σf, E, and HM of printable polymers were lower than those of the control group, and specimens did not fracture in bend testing. In contrast, KIC and ωe were the highest for a printable polymer. Therefore, tension tests should be considered when testing ductile materials.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalDenture BasesPolymersMaterials TestingElastic ModulusFlexural StrengthHardnessDental MaterialsIn Vitro Techniques

Substanzen

PolymersDental Materials

Autor:innen und Institutionen

  • Research Associate, Material Science Unit, Department of Prosthetic Dentistry, University Hospital, LMU Munich, Germany. Electronic address: andrea.coldea@med.uni-muenchen.de.
  • Research Associate, Material Science Unit, Department of Prosthetic Dentistry, University Hospital, LMU Munich, Germany.
  • Dental Technician, Material Science Unit, Department of Prosthetic Dentistry, University Hospital, LMU Munich, Munich, Germany.
  • Professor, Material Science Unit, Department of Prosthetic Dentistry, University Hospital, LMU Munich, Munich, Germany.

Zitieren

APA

Coldea, A., Mayinger, F., Meinen, J., Hoffmann, M., & Stawarczyk, B. (2025). Mechanical properties of 3D printed denture base polymers. The Journal of Prosthetic Dentistry, 133(5), 1361.e1-1361.e8. https://doi.org/10.1016/j.prosdent.2025.02.009

Vancouver

Coldea A, Mayinger F, Meinen J, Hoffmann M, Stawarczyk B. Mechanical properties of 3D printed denture base polymers. The Journal of Prosthetic Dentistry. 2025;133(5):1361.e1-1361.e8. doi:10.1016/j.prosdent.2025.02.009

BibTeX
@article{Coldea2025,
  author = {Coldea, Andrea and Mayinger, Felicitas and Meinen, John and Hoffmann, Moritz and Stawarczyk, Bogna},
  title = {Mechanical properties of 3D printed denture base polymers},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2025},
  volume = {133},
  number = {5},
  pages = {1361.e1--1361.e8},
  doi = {10.1016/j.prosdent.2025.02.009}
}
Kostenlos starten →