Modification of the Mechanical Properties of Photosensitive Resin by Using Biobased Fillers During Stereolithography (SLA) 3D Printing
Materials · 08.06.2025 · 18 (12) · 2699
DOI: 10.3390/ma18122699 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 08.06.2025. Verfasst von Miroslav Müller und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Material Science and Manufacturing Technology, Faculty of Engineering, Czech University of Life Sciences Prague, Kamycka 129, Suchdol, …. Die Arbeit wurde bisher 20-mal zitiert (Crossref) und nennt 55 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Internal grant agency of Faculty of Engineering, Czech University of Life Sciences Prague grant no. 2024:31140/1312/3102: "Research of factors affecting ecolog…, Internal grant agency of Faculty of Engineering, Czech University of Life Sciences Prague grant no. 2025:31140/1312/3104: "Research into the production of comp…, Internal grant agency of Faculty of Engineering, Czech University of Life Sciences Prague.
Abstract (Originalsprache)
This paper is focused on the modification of commercial resin by using biobased fillers during stereolithography (SLA) 3D printing. This research aims to create a composite material with a matrix made of commercially available photosensitive resin modified with a filler based on secondary raw materials and materials formed as by-products in the processing of biological materials. The research determines the effect of different fillers on the tensile properties and hardness of samples printed using SLA 3D printing, and it also investigates their integrity using SEM analysis. This study aims to evaluate the feasibility of using these fillers for producing 3D-printed parts with SLA technology. The results of this study open up new possibilities for designing modified composite materials based on additive SLA 3D-printing technology using biological fillers. Within the framework of research activities, a positive effect on tensile properties and an improved interfacial interface between the matrix and the filler was demonstrated for several tested fillers. Significant increases in tensile strength of up to 22% occurred in composite systems filled with cotton flakes (CF), miscanthus (MS), walnut (WN), spruce tree (SB), wheat (WT) and eggshells (ES). Significant potential for further research activities and added value was shown by most of the tested bio-fillers. A significant contribution of the current research is the demonstration of the improved mechanical performance of photosensitive resin modified with natural fillers.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Material Science and Manufacturing Technology, Faculty of Engineering, Czech University of Life Sciences Prague, Kamycka 129, Suchdol, 165 00 Prague, Czech Republic.
ORCID-Profile: Miroslav Müller, Jiří Urban, Rajesh Kumar Mishra
Förderung
- Internal grant agency of Faculty of Engineering, Czech University of Life Sciences Prague grant no. 2024:31140/1312/3102: "Research of factors affecting ecolog…
- Internal grant agency of Faculty of Engineering, Czech University of Life Sciences Prague grant no. 2025:31140/1312/3104: "Research into the production of comp…
- Internal grant agency of Faculty of Engineering, Czech University of Life Sciences Prague
Zitieren
APA
Müller, M., Urban, J., Svobodová, J., & Mishra, R. K. (2025). Modification of the Mechanical Properties of Photosensitive Resin by Using Biobased Fillers During Stereolithography (SLA) 3D Printing. Materials, 18(12), 2699. https://doi.org/10.3390/ma18122699
Vancouver
Müller M, Urban J, Svobodová J, Mishra RK. Modification of the Mechanical Properties of Photosensitive Resin by Using Biobased Fillers During Stereolithography (SLA) 3D Printing. Materials. 2025;18(12):2699. doi:10.3390/ma18122699
BibTeX
@article{Mller2025,
author = {Müller, Miroslav and Urban, Jiří and Svobodová, Jaroslava and Mishra, Rajesh Kumar},
title = {Modification of the Mechanical Properties of Photosensitive Resin by Using Biobased Fillers During Stereolithography (SLA) 3D Printing},
journal = {Materials},
year = {2025},
volume = {18},
number = {12},
pages = {2699},
doi = {10.3390/ma18122699}
}
EUVIMED