EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Mechanical Properties’ Strengthening of Photosensitive 3D Resin in Lithography Technology Using Acrylated Natural Rubber

Wasan Tessanan, Philippe Daniel, Pranee Phinyocheep

Polymers · 17.10.2023 · 15 (20) · 4110

DOI: 10.3390/polym15204110 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 17.10.2023. Verfasst von Wasan Tessanan und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Chemistry, Faculty of Science, Mahidol University, Rama VI Road, Payathai, Bangkok 10400, Thailand. Die Arbeit wurde bisher 11-mal zitiert (Crossref) und nennt 55 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Erasmus+, ERASMUS+ Thailand, Science Achievement Scholarship of Thailand (SAST).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Acrylated natural rubber (ANR) with various acrylate contents (0.0–3.5 mol%) was prepared from natural rubber as a raw material and then incorporated with commercial 3D resin to fabricate specimens using digital light processing. As a result, the utilization of ANR with 1.5 mol% acrylate content could provide the maximum improvement in stretchability and impact strength, approximately 155% and 221%, respectively, over using pure 3D resin, without significant deterioration of tensile modulus and mechanical strength. According to evidence from a scanning electron microscope, this might be due to the partial interaction between the dispersed small rubber particles and the resin matrix. Additionally, the glass-transition temperature of the 3D-printed sample shifted to a lower temperature by introducing a higher acrylate content in the ANR. Therefore, this work might offer a practical way to effectively enhance the properties of the fundamental commercial 3D resin and broaden its applications. It also makes it possible to use natural rubber as a bio-based material in light-based 3D printing.

Schlagwörter

Stichwörter der Autor:innen

acrylated natural rubberbio-based materialdigital light 3D printing processingmodified natural rubbernatural rubber

Autor:innen und Institutionen

  • Department of Chemistry, Faculty of Science, Mahidol University, Rama VI Road, Payathai, Bangkok 10400, Thailand.
  • Institut des Molécules et des Matériaux du Mans (IMMM), UMR CNRS 6283, Faculté des Sciences et Technologie, Le Mans Université, Bd O. Messiaen, CEDEX 09, 72085 Le Mans, France.

Förderung

  • Erasmus+
  • ERASMUS+ Thailand
  • Science Achievement Scholarship of Thailand (SAST)

Zitieren

APA

Tessanan, W., Daniel, P., & Phinyocheep, P. (2023). Mechanical Properties’ Strengthening of Photosensitive 3D Resin in Lithography Technology Using Acrylated Natural Rubber. Polymers, 15(20), 4110. https://doi.org/10.3390/polym15204110

Vancouver

Tessanan W, Daniel P, Phinyocheep P. Mechanical Properties’ Strengthening of Photosensitive 3D Resin in Lithography Technology Using Acrylated Natural Rubber. Polymers. 2023;15(20):4110. doi:10.3390/polym15204110

BibTeX
@article{Tessanan2023,
  author = {Tessanan, Wasan and Daniel, Philippe and Phinyocheep, Pranee},
  title = {Mechanical Properties’ Strengthening of Photosensitive 3D Resin in Lithography Technology Using Acrylated Natural Rubber},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {20},
  pages = {4110},
  doi = {10.3390/polym15204110}
}
Kostenlos starten →