Bonding Orthodontic Attachments to 3D-Printed Photosensitive Definitive Resin: An In Vitro Study
Dentistry Journal · 24.07.2025 · 13 (8) · 341
DOI: 10.3390/dj13080341 ↗Kurz gefasst
Fachartikel in der Zeitschrift Dentistry Journal, online erschienen am 24.07.2025. Verfasst von Omaika Victoria Criollo-Barrios und 5 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Dentistry, Autonomous University of Tamaulipas, Av. Universidad esq. con Blvd. Adolfo López Mateos s/n, Tampico C.P., Ciudad Victoria 8933…. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 45 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
Background/Objectives: The increasing clinical integration of 3D-printed definitive resins requires a comprehensive understanding of their physicochemical properties and adhesive behavior. However, there is limited evidence regarding the optimal surface treatment and bonding strategies for clear aligner composite attachments on these materials. This study aimed to characterize a 3D-printed definitive resin, evaluate the effects of surface treatments on its surface topography, and compare the shear bond strength (SBS) of the bonded attachments using different adhesive systems, both before and after thermocycling.
Methods
A total of 120 rectangular specimens were fabricated from a 3D printed dental resin (Crowntec®, SAREMCO Dental AG—Mexico City, Mexico). For physicochemical characterization, six samples underwent scanning electron microscopy/energy-dispersive spectroscopy, X-ray diffraction, and thermogravimetric analysis. To evaluate surface topography, 42 polished specimens were assigned to three groups: untreated (control), etched with 4% hydrofluoric acid (HFA), or sandblasted with 50 µm Al2O3 (AA). Each group was subdivided for SEM observation and surface roughness (Ra) measurement. For SBS testing, 72 additional samples received the same surface treatments and were further subdivided according to the adhesive system: Transbond™ XT Primer (TXT) or Single Bond Universal (SBU).
Results
The AA group showed the highest Ra (2.21 ± 0.30 µm), followed by HFA (0.81 ± 0.20 µm) and control (0.07 ± 0.30 µm) (p < 0.001). The highest SBS was observed in the AA + SBU group, followed by AA + TXT.
Conclusions
Sandblasting with Al2O3 particles, combined with a universal adhesive, significantly improved bond strength, suggesting a viable protocol for 3D printed definitive composites in aligner attachment applications.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Faculty of Dentistry, Autonomous University of Tamaulipas, Av. Universidad esq. con Blvd. Adolfo López Mateos s/n, Tampico C.P., Ciudad Victoria 89337, Mexico.
- CEETEPS-State Center of Technological Education "Paula Souza", Department of Mechanical Manufacturing, Av. Antônia Rosa Fioravante 804, Mauá 09390-120, SP, Brazil.
ORCID-Profile: Ronaldo Câmara Cozza
Zitieren
APA
Criollo-Barrios, O. V., Luna-Domínguez, C. R., Luna-Lara, C. A., Figueroa-López, R. J., Cozza, R. C., & Luna-Domínguez, J. H. (2025). Bonding Orthodontic Attachments to 3D-Printed Photosensitive Definitive Resin: An In Vitro Study. Dentistry Journal, 13(8), 341. https://doi.org/10.3390/dj13080341
Vancouver
Criollo-Barrios OV, Luna-Domínguez CR, Luna-Lara CA, Figueroa-López RJ, Cozza RC, Luna-Domínguez JH. Bonding Orthodontic Attachments to 3D-Printed Photosensitive Definitive Resin: An In Vitro Study. Dentistry Journal. 2025;13(8):341. doi:10.3390/dj13080341
BibTeX
@article{CriolloBarrios2025,
author = {Criollo-Barrios, Omaika Victoria and Luna-Domínguez, Carlos Roberto and Luna-Lara, Carlos Alberto and Figueroa-López, Ricardo de Jesus and Cozza, Ronaldo Câmara and Luna-Domínguez, Jorge Humberto},
title = {Bonding Orthodontic Attachments to 3D-Printed Photosensitive Definitive Resin: An In Vitro Study},
journal = {Dentistry Journal},
year = {2025},
volume = {13},
number = {8},
pages = {341},
doi = {10.3390/dj13080341}
}
EUVIMED