EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Mechanical Properties of 3D-Printed Occlusal Splint Materials

Vladimir Prpic iD, Filipa Spehar iD, Dominik Stajdohar, Roko Bjelica iD, Samir Cimic iD, Matej Par iD

Dentistry Journal · 18.08.2023 · 11 (8) · 199

DOI: 10.3390/dj11080199 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Dentistry Journal, online erschienen am 18.08.2023. Verfasst von Vladimir Prpic und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Fixed Prosthodontics, School of Dental Medicine, University of Zagreb, 10000 Zagreb, Croatia. Die Arbeit wurde bisher 44-mal zitiert (Crossref) und nennt 34 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Data regarding the mechanical properties of three-dimensionally (3D) printed materials for occlusal splint manufacturing are scarce. The aim of the present study was to evaluate the flexural strength and surface hardness of modern 3D-printed occlusal splint materials and compare them with two control groups, namely, milled and conventional cold-polymerized occlusal splint materials. A total of 140 rectangular specimens were manufactured for the present study. The specimens were prepared in accordance with the International Organization for Standardization standards (ISO 20795-1:2013). Five 3D-printed (NextDent Ortho Rigid, Dental LT Clear, Dentona Flexisplint, Cosmos Bite Splint, and ProArt Print Splint), one milled (ProArt CAD Splint), and one cold-polymerized (ProBase Cold) occlusal splint materials were used to determine flexural strength and surface hardness values. The three-point flexure test was used for the determination of flexural strength values, while Vickers hardness was measured to determine surface hardness. Ten specimens (n = 10) of each material were tested using these procedures. One-way ANOVA and Tukey’s post-hoc test were used to analyze the obtained results (α = 0.05). The values of flexural strength ranged from 46.1 ± 8.2 MPa to 106 ± 8.3 MPa. The Vickers hardness values ranged from 4.9 ± 0.5 VHN to 20.6 ± 1.3 VHN. Significant differences were found among the tested materials (p < 0.0001). The milled and cold-polymerized materials yielded higher values for both flexural strength (only one 3D-printed resin had comparable results to cold-polymerized acrylics) and surface hardness. There are differences in the mechanical properties of the various tested occlusal splint materials. The flexural strength of most of the 3D-printed materials and their surface hardness values are still inferior when compared to the milled or cold-polymerized materials.

Schlagwörter

Stichwörter der Autor:innen

3D-printedflexural strengthmilledocclusal splintsurface hardness

Autor:innen und Institutionen

  • Department of Fixed Prosthodontics, School of Dental Medicine, University of Zagreb, 10000 Zagreb, Croatia.
  • School of Dental Medicine, University of Zagreb, 10000 Zagreb, Croatia.
  • Department of Oral Surgery, School of Dental Medicine, University of Zagreb, 10000 Zagreb, Croatia.
  • Department of Removable Prosthodontics, School of Dental Medicine, University of Zagreb, 10000 Zagreb, Croatia.
  • Department of Endodontics and Restorative Dentistry, School of Dental Medicine, University of Zagreb, 10000 Zagreb, Croatia.

ORCID-Profile: Vladimir Prpic, Filipa Spehar, Roko Bjelica, Samir Cimic, Matej Par

Zitieren

APA

Prpic, V., Spehar, F., Stajdohar, D., Bjelica, R., Cimic, S., & Par, M. (2023). Mechanical Properties of 3D-Printed Occlusal Splint Materials. Dentistry Journal, 11(8), 199. https://doi.org/10.3390/dj11080199

Vancouver

Prpic V, Spehar F, Stajdohar D, Bjelica R, Cimic S, Par M. Mechanical Properties of 3D-Printed Occlusal Splint Materials. Dentistry Journal. 2023;11(8):199. doi:10.3390/dj11080199

BibTeX
@article{Prpic2023,
  author = {Prpic, Vladimir and Spehar, Filipa and Stajdohar, Dominik and Bjelica, Roko and Cimic, Samir and Par, Matej},
  title = {Mechanical Properties of 3D-Printed Occlusal Splint Materials},
  journal = {Dentistry Journal},
  year = {2023},
  volume = {11},
  number = {8},
  pages = {199},
  doi = {10.3390/dj11080199}
}
Kostenlos starten →