EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Aging Processes and Their Influence on the Mechanical Properties of Printable Occlusal Splint Materials

Jan Raffael Rosello Jimenez, Florian Fuchs, Leonie Schmohl, Michaela Schulz-Siegmund, Andreas Koenig iD

Polymers · 29.11.2023 · 15 (23) · 4574

DOI: 10.3390/polym15234574 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 29.11.2023. Verfasst von Jan Raffael Rosello Jimenez und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics and Material Sciences, Leipzig University, 04103 Leipzig, Germany. Die Arbeit wurde bisher 14-mal zitiert (Crossref) und nennt 46 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Three-dimensional (3D)-printed occlusal splints are becoming more prevalent in the treatment of tooth substance loss due to their fast and cost-effective production. The purpose of this in vitro study was to investigate whether the mechanical properties (tensile strength—TS, modulus of elasticity in tension—ME, and Vickers hardness—HV) vary between the materials (printed dimethacrylate-based resins: Keyprint KeySplint soft—KEY, Luxaprint Ortho Plus—LUX, V-Print splint—VPR, printed methacrylate-based resins Freeprint splint 2.0—FRE, and milled methacrylate-based material, CLEAR splint—CLE), and the influence of aging processes (extraoral storage conditions and nightly or daily use) was examined. The printed methacrylate-based resins (FRE, LUX, and VPR) had much higher TS (43.7–48.5 MPa compared to 12.3–13.3 MPa), higher ME (2.01–2.37 GPa compared to 0.43–0.72 GPa), and higher HV (11.8–15.0 HV compared to 3.3–3.5 HV) than both of the methacrylate-based resins (KEY and CLE) after the production process. Although the TS, ME, and HV of the printed dimethacrylate resins (FRE, LUX, and VPR) decreased significantly under humid conditions with possibly elevated temperatures (thermocycling as well as 37 °C), these mechanical properties were significantly higher than both methacrylate-based resins (KEY and CLE). Therefore, printed dimethacrylate resins should be used rather than methacrylate-based resins for high expected masticatory forces, low wall thicknesses, or very long wearing times (≥6 months).

Schlagwörter

Stichwörter der Autor:innen

3D printedVickers hardnessYoung’s modulusbite splintselastic modulustensile strengththermocycling

Autor:innen und Institutionen

  • Department of Prosthodontics and Material Sciences, Leipzig University, 04103 Leipzig, Germany.
  • Private Practice, Zahnarztpraxis Jan Rosello, 04654 Frohburg, Germany.
  • Institute of Pharmacy, Pharmaceutical Technology, Leipzig University, 04317 Leipzig, Germany.

ORCID-Profile: Andreas Koenig

Zitieren

APA

Rosello Jimenez, J. R., Fuchs, F., Schmohl, L., Schulz-Siegmund, M., & Koenig, A. (2023). Aging Processes and Their Influence on the Mechanical Properties of Printable Occlusal Splint Materials. Polymers, 15(23), 4574. https://doi.org/10.3390/polym15234574

Vancouver

Rosello Jimenez JR, Fuchs F, Schmohl L, Schulz-Siegmund M, Koenig A. Aging Processes and Their Influence on the Mechanical Properties of Printable Occlusal Splint Materials. Polymers. 2023;15(23):4574. doi:10.3390/polym15234574

BibTeX
@article{RoselloJimenez2023,
  author = {Rosello Jimenez, Jan Raffael and Fuchs, Florian and Schmohl, Leonie and Schulz-Siegmund, Michaela and Koenig, Andreas},
  title = {Aging Processes and Their Influence on the Mechanical Properties of Printable Occlusal Splint Materials},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {23},
  pages = {4574},
  doi = {10.3390/polym15234574}
}
Kostenlos starten →