EUVIMEDEUVIMED entdecken
Crossref

Wear resistance of 3D printed occlusal device materials

Nathaniel C Lawson, Pierpont Brown, Suleiman Hamdan, Aaron Alford, Amir H Nejat

The Journal of Prosthetic Dentistry · 2025-02 · 133 (2) · 576.e1-576.e6

DOI: 10.1016/j.prosdent.2024.10.021 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2025-02. Verfasst von Nathaniel C Lawson und 4 weiteren Autor:innen. Beteiligte Einrichtung: Associate Professor, Department of Clinical and Community Sciences, The University of Alabama at Birmingham School of Dentistry, Birmingham, Ala. Ele…. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Dental Materials, Dental Restoration Wear, Occlusal Splints. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 24 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: Three-dimensional (3D) printing offers an efficient method of producing occlusal devices; however, their wear resistance is poorly understood. PURPOSE: The purpose of this in vitro study was to compare the wear resistance of flexible and rigid 3D printed occlusal device materials with milled and conventionally processed occlusal device materials. MATERIAL AND METHODS: Blocks (n=8) of 3 flexible 3D printed materials (KeySplint Soft, NightGuard Flex 2, SmileGuard), 2 rigid 3D printed materials (KeySplint Hard, NightGuard Firm 2), 1 milled material (Ceramill A-Splint), 1 thermoform material (Erkoloc-Pro), 1 light-polymerized material (Eclipse Prosthetic Resin), 1 heat-polymerized material (Excel Formula Heat Cure Denture Base Material), and 1 autopolymerized material (Great Lakes Splint Resin Acrylic) were prepared and wet polished with 1200-grit SiC paper. The specimens were placed in a modified Alabama wear testing device with spherical zirconia antagonists. The devices applied a 20-N load and 2-mm horizontal slide for 400 000 cycles, and the test was run in a 33% glycerin solution. Following the wear test, the volumetric wear was measured with an optical profilometer. The Vickers microhardness of the materials was also measured (n=3). Volumetric wear and microhardness were compared with 1-way ANOVAs and Tukey post hoc analyses (α=.05). RESULTS: Significant differences were found between the wear of the different occlusal device materials (P

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalDental MaterialsDental Restoration WearOcclusal SplintsMaterials TestingHumansIn Vitro Techniques

Substanzen

Dental Materials

Autor:innen und Institutionen

  • Associate Professor, Department of Clinical and Community Sciences, The University of Alabama at Birmingham School of Dentistry, Birmingham, Ala. Electronic address: nlawson@uab.edu.
  • Resident, Department of Orthodontics, The University of Alabama at Birmingham School of Dentistry, Birmingham, Ala.
  • Associate Professor, Division of Prosthodontics, Louisiana State University School of Dentistry, New Orleans, LA.
  • Instructor, Department of Chemistry, The University of Alabama at Birmingham College of Arts and Sciences, Birmingham, Ala.
  • Assistant Professor, Division of Prosthodontics, Louisiana State University School of Dentistry, New Orleans, LA.

Zitieren

APA

Lawson, N. C., Brown, P., Hamdan, S., Alford, A., & Nejat, A. H. (2025). Wear resistance of 3D printed occlusal device materials. The Journal of Prosthetic Dentistry, 133(2), 576.e1-576.e6. https://doi.org/10.1016/j.prosdent.2024.10.021

Vancouver

Lawson NC, Brown P, Hamdan S, Alford A, Nejat AH. Wear resistance of 3D printed occlusal device materials. The Journal of Prosthetic Dentistry. 2025;133(2):576.e1-576.e6. doi:10.1016/j.prosdent.2024.10.021

BibTeX
@article{Lawson2025,
  author = {Lawson, Nathaniel C and Brown, Pierpont and Hamdan, Suleiman and Alford, Aaron and Nejat, Amir H},
  title = {Wear resistance of 3D printed occlusal device materials},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2025},
  volume = {133},
  number = {2},
  pages = {576.e1--576.e6},
  doi = {10.1016/j.prosdent.2024.10.021}
}
Kostenlos starten →