EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Physico-Mechanical Properties of 3D-Printed Filament Materials for Mouthguard Manufacturing

Maciej Trzaskowski iD, Gen Tanabe, Hiroshi Churei iD, Toshiaki Ueno iD, Michał Ziętala iD, Bartłomiej Wysocki iD, Judyta Sienkiewicz iD, Agata Szczesio-Włodarczyk iD, Jerzy Sokołowski, Ewa Czochrowska iD, Małgorzata Zadurska, Elżbieta Mierzwińska-Nastalska und 2 weitere

Polymers · 10.08.2025 · 17 (16) · 2190

DOI: 10.3390/polym17162190 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 10.08.2025. Verfasst von Maciej Trzaskowski und 13 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Medical University of Warsaw, 02-091 Warsaw, Poland. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 73 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Multidisciplinary Research Centre of Cardinal Stefan Wyszynski University in Warsaw, project Towards Innovations within the Excellent Science Program.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Mouthguards are recommended for all sports that may cause injuries to the head and oral cavity. Custom mouthguards, made conventionally in the thermoforming process from ethylene vinyl acetate (EVA), face challenges with thinning at the incisor area during the process. In contrast, additive manufacturing (AM) processes enable the precise reproduction of the dimensions specified in a computer-aided design (CAD) model. The potential use of filament extrusion materials in the fabrication of custom mouthguards has not yet been explored in comparative studies. Our research aimed to compare five commercially available filaments for the material extrusion (MEX) also known as fused deposition modelling (FDM) of custom mouthguards using a desktop 3D printer. Samples made using Copper 3D PLActive, Spectrum Medical ABS, Braskem Bio EVA, DSM Arnitel ID 2045, and NinjaFlex were compared to EVA Erkoflex, which served as a control sample. The samples underwent tests for ultimate tensile strength (UTS), split Hopkinson pressure bar (SHPB) performance, drop-ball impact, abrasion resistance, absorption, and solubility. The results showed that Copper 3D PLActive and Spectrum Medical ABS had the highest tensile strength. DSM Arnitel ID 2045 had the highest dynamic property performance, measured with the SHPB and drop-ball tests. On the other hand, NinjaFlex exhibited the lowest abrasion resistance and the highest absorption and solubility. DSM Arnitel ID 2045’s absorption and solubility levels were comparable to those of EVA, but had significantly lower abrasion resistance. Ultimately, DSM Arnitel ID 2045 is recommended as the best filament for 3D-printing mouthguards. The properties of this biocompatible material ensure high-impact energy absorption while maintaining low fluid sorption and solubility, supporting its safe intra-oral application for mouthguard fabrication. However, its low abrasion resistance indicated that mouthguards made from this material may need to be replaced more frequently.

Schlagwörter

Stichwörter der Autor:innen

3D printingCAD/CAMFDM printingabrasion resistanceadditive manufacturingdental materialsdental traumadynamic propertiesmaterial extrusionpolymerssport dentistry

Autor:innen und Institutionen

  • Department of Prosthodontics, Medical University of Warsaw, 02-091 Warsaw, Poland.
  • Department of Sport Dentistry, School of Dentistry, Meikai University, Sakado 350-0248, Japan.
  • Department of Masticatory Function and Health Science, Institute of Science, Tokyo 113-8510, Japan.
  • Multidisciplinary Research Center, Cardinal Stefan Wyszynski University in Warsaw, 05-092 Dziekanów Leśny, Poland.
  • Faculty of Mechatronics, Armament and Aerospace, Military University of Technology, 00-908 Warsaw, Poland.
  • University Laboratory of Materials Research, Medical University of Lodz, 90-419 Lodz, Poland.

ORCID-Profile: Maciej Trzaskowski, Hiroshi Churei, Toshiaki Ueno, Michał Ziętala, Bartłomiej Wysocki, Judyta Sienkiewicz, Agata Szczesio-Włodarczyk, Ewa Czochrowska, Jolanta Kostrzewa-Janicka, Katarzyna Mańka-Malara

Förderung

  • Multidisciplinary Research Centre of Cardinal Stefan Wyszynski University in Warsaw
  • project Towards Innovations within the Excellent Science Program

Zitieren

APA

Trzaskowski, M., Tanabe, G., Churei, H., Ueno, T., Ziętala, M., Wysocki, B., Sienkiewicz, J., Szczesio-Włodarczyk, A., Sokołowski, J., Czochrowska, E., Zadurska, M., Mierzwińska-Nastalska, E., Kostrzewa-Janicka, J., & Mańka-Malara, K. (2025). Physico-Mechanical Properties of 3D-Printed Filament Materials for Mouthguard Manufacturing. Polymers, 17(16), 2190. https://doi.org/10.3390/polym17162190

Vancouver

Trzaskowski M, Tanabe G, Churei H, Ueno T, Ziętala M, Wysocki B, et al. Physico-Mechanical Properties of 3D-Printed Filament Materials for Mouthguard Manufacturing. Polymers. 2025;17(16):2190. doi:10.3390/polym17162190

BibTeX
@article{Trzaskowski2025,
  author = {Trzaskowski, Maciej and Tanabe, Gen and Churei, Hiroshi and Ueno, Toshiaki and Ziętala, Michał and Wysocki, Bartłomiej and Sienkiewicz, Judyta and Szczesio-Włodarczyk, Agata and Sokołowski, Jerzy and Czochrowska, Ewa and Zadurska, Małgorzata and Mierzwińska-Nastalska, Elżbieta and Kostrzewa-Janicka, Jolanta and Mańka-Malara, Katarzyna},
  title = {Physico-Mechanical Properties of 3D-Printed Filament Materials for Mouthguard Manufacturing},
  journal = {Polymers},
  year = {2025},
  volume = {17},
  number = {16},
  pages = {2190},
  doi = {10.3390/polym17162190}
}
Kostenlos starten →