EUVIMEDEUVIMED entdecken
Crossref

Effects of different types of molds on the color difference, translucency, surface roughness, and hardness of a maxillofacial silicone elastomer

Ceyda B İnal, Merve Bankoğlu Güngör, Bilge Turhan Bal, Seçil Karakoca Nemli

Journal of Oral Science · 2025

DOI: 10.2334/josnusd.24-0212 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Oral Science, 2025. Verfasst von Ceyda B İnal und 3 weiteren Autor:innen. Beteiligte Einrichtung: Private Practice. Hauptthemen laut MEDLINE: Silicone Elastomers, Maxillofacial Prosthesis. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 34 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

PURPOSE: The purpose of the present study was to evaluate the effects of dental stone molds and three dimensional (3D)-printed molds on the color difference, translucency, surface roughness, and hardness of maxillofacial silicones. METHODS: To prepare molds, a rectangular body 20 mm in diameter and 2 mm in thickness, was designed with computer-aided design software. Two different dental gypsum molds were prepared with the lost-wax technique. Silicone mixture was poured into molds and polymerized at room temperature for 24 h. Color parameters were measured using a spectrophotometer. A profilometer was used for measuring surface roughness, and Shore A values were obtained with a durometer. RESULTS: Color change (ΔE00) values of the 3D-resin group (1.53 ± 0.35) were significantly lower than others. The highest translucency parameter (TP) values belonged to the stainless steel group (12.44 ± 0.65). Surface roughness values (Ra) of the stainless steel group (0.28 ± 0.06) were significantly lower than other groups. The mean Shore A value of the 3D-resin group (23.90 ± 1.37) was significantly higher than the blue gypsum group (21.53 ± 0.93). CONCLUSION: Lower color difference and higher Shore A values were examined with 3D-printed resin molds. The highest TP values and lowest Ra values were obtained when stainless steel was used for molding of maxillofacial silicone.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Silicone ElastomersMaxillofacial ProsthesisSurface PropertiesColorHardnessMaterials TestingPrinting, Three-DimensionalComputer-Aided DesignSpectrophotometry

Stichwörter der Autor:innen

3D-printingcolorhardnessmaxillofacial prosthesisroughness

Substanzen

Silicone Elastomers

Autor:innen und Institutionen

  • Private Practice.
  • Department of Prosthodontics, Faculty of Dentistry, Gazi University.

Zitieren

APA

İnal, C. B., Bankoğlu Güngör, M., Turhan Bal, B., & Karakoca Nemli, S. (2025). Effects of different types of molds on the color difference, translucency, surface roughness, and hardness of a maxillofacial silicone elastomer. Journal of Oral Science. https://doi.org/10.2334/josnusd.24-0212

Vancouver

İnal CB, Bankoğlu Güngör M, Turhan Bal B, Karakoca Nemli S. Effects of different types of molds on the color difference, translucency, surface roughness, and hardness of a maxillofacial silicone elastomer. Journal of Oral Science. 2025. doi:10.2334/josnusd.24-0212

BibTeX
@article{nal2025,
  author = {İnal, Ceyda B and Bankoğlu Güngör, Merve and Turhan Bal, Bilge and Karakoca Nemli, Seçil},
  title = {Effects of different types of molds on the color difference, translucency, surface roughness, and hardness of a maxillofacial silicone elastomer},
  journal = {Journal of Oral Science},
  year = {2025},
  doi = {10.2334/josnusd.24-0212}
}
Kostenlos starten →